B1B73 Jeep Code - Left Side Satellite Acceleration Sensor 2 Internal
Quick Answer
The Left Side Impact Sensor 2 is located in the C-pillar area just past the 2nd row doors. Common causes include Faulty Left Side Impact Sensor 2, Left Side Impact Sensor 2 harness is open or shorted, Left Side Impact Sensor 2 circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1B73 Jeep indicates Left Side Satellite Acceleration Sensor 2 Internal.
- Common causes
- Common causes include Faulty Left Side Impact Sensor 2, Left Side Impact Sensor 2 harness is open or shorted, Left Side Impact Sensor 2 circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B1B73 Jeep Description
What are the Possible Causes of the DTC B1B73 Jeep?
- Faulty Left Side Impact Sensor 2
- Left Side Impact Sensor 2 harness is open or shorted
- Left Side Impact Sensor 2 circuit poor electrical connection
- Faulty Occupant Restraint Controller (ORC)
How to Fix the DTC B1B73 Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B1B73 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B1B73 Jeep code?
Need more information on how to fix the B1B73 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1B73 Jeep code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1B73 Jeep Code
1. What are common symptoms of OBDII code B1B73 in a Jeep related to the Left Side Satellite Acceleration Sensor 2 Internal?
The common symptoms include the airbag warning light illuminating on the dashboard and potential issues with the vehicle's airbag system.
2. What could cause the OBDII code B1B73 to appear in a Jeep?
The code B1B73 typically appears due to a malfunction or internal fault in the Left Side Satellite Acceleration Sensor 2 of the airbag system.
3. How serious is the OBDII code B1B73 in a Jeep?
The code B1B73 should be taken seriously as it indicates a problem with the airbag system, which may affect its proper deployment in the event of a collision.
4. Can I continue driving my Jeep with the OBDII code B1B73 present?
It is not recommended to drive the vehicle with the B1B73 code, as it may compromise the functionality of the airbag system. It is advisable to address the issue promptly.
5. What is the typical repair for OBDII code B1B73 in a Jeep?
Repairing the B1B73 code usually involves diagnosing the specific issue with the Left Side Satellite Acceleration Sensor 2 and either repairing or replacing the sensor as needed.
6. Are there any DIY tips for troubleshooting the OBDII code B1B73 in a Jeep?
While it's possible to visually inspect the sensor and its connections for any obvious issues, diagnosing and repairing the B1B73 code often requires specialized tools and knowledge best handled by a professional.
7. How much does it cost to repair the OBDII code B1B73 in a Jeep?
The cost of repairing the B1B73 code can vary depending on the extent of the issue, the need for sensor replacement, and labor costs. It's advisable to get a diagnosis from a trusted mechanic for an accurate estimate.
8. Can resetting the OBDII code B1B73 in a Jeep solve the issue temporarily?
Resetting the code may temporarily turn off the warning light, but it will not fix the underlying problem causing the B1B73 code. It's crucial to address the root cause of the issue for a permanent solution.
9. How long does it take to repair the OBDII code B1B73 in a Jeep?
The repair time for the B1B73 code can vary depending on the exact cause of the issue and the availability of parts. In general, it may take a few hours to a day for a professional mechanic to diagnose and repair the problem.
10. Is it safe to drive a Jeep with the airbag system affected by the OBDII code B1B73?
Driving a vehicle with a malfunctioning airbag system, indicated by the B1B73 code, is not safe as it may compromise the effectiveness of the airbags in case of an accident. It is recommended to have the issue fixed promptly.
Discuss the causes and fixes for B1B73 Jeep OBDII Code
Code B1B73 Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
