B1B28 Jeep Code - 1st Row Driver Seat Belt Pretensioner Circuit Low
Quick Answer
The Occupant Restraint Controller (ORC) monitors the 1st Row Driver Seat Belt Pretensioner Circuit. Common causes include Faulty Driver Seat Belt Pretensioner, Driver Seat Belt Pretensioner harness is open or shorted, Driver Seat Belt Pretensioner circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1B28 Jeep indicates 1st Row Driver Seat Belt Pretensioner Circuit Low.
- Common causes
- Common causes include Faulty Driver Seat Belt Pretensioner, Driver Seat Belt Pretensioner harness is open or shorted, Driver Seat Belt Pretensioner circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B1B28 Jeep Description
What are the Possible Causes of the DTC B1B28 Jeep?
- Faulty Driver Seat Belt Pretensioner
- Driver Seat Belt Pretensioner harness is open or shorted
- Driver Seat Belt Pretensioner circuit poor electrical connection
- Faulty Occupant Restraint Controller (ORC)
How to Fix the DTC B1B28 Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B1B28 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B1B28 Jeep code?
Need more information on how to fix the B1B28 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1B28 Jeep code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1B28 Jeep Code
1. What does the OBDII code B1B28 mean on a Jeep?
The B1B28 code indicates a problem in the 1st Row Driver Seat Belt Pretensioner Circuit, specifically that the circuit voltage is too low.
2. What are the common symptoms of the B1B28 code?
Common symptoms include the airbag warning light being illuminated, the seat belt pretensioner not functioning properly, and potential loss of airbag system functionality.
3. What causes the B1B28 code on a Jeep?
The code can be caused by a damaged seat belt pretensioner, faulty wiring or connectors, corroded terminals, or a malfunctioning airbag control module.
4. Is it safe to drive with the B1B28 code active?
No, it’s not recommended to drive with this code active because it may indicate a fault in the airbag or seat belt system, which are critical for safety in an accident.
5. How do I diagnose the B1B28 code?
Diagnosis involves inspecting the seat belt pretensioner and its wiring, checking for corrosion or damage, and using a scan tool to confirm the fault.
6. Can a low battery cause the B1B28 code?
Yes, a weak or low battery voltage can sometimes trigger this code, as the airbag system components rely on stable power.
7. How do I fix the B1B28 code on a Jeep?
Repairs may include replacing the seat belt pretensioner, repairing or replacing damaged wiring or connectors, and clearing the code with a diagnostic tool.
8. How much does it cost to fix the B1B28 code?
The cost varies depending on the issue, but replacing a seat belt pretensioner can cost between $200 and $500, plus diagnostic and labor fees.
9. Can I reset the B1B28 code without fixing the issue?
You can clear the code with a scan tool, but it will likely return if the underlying issue isn’t resolved.
10. What tools are needed to troubleshoot the B1B28 code?
You’ll need a diagnostic scan tool, a multimeter to check voltage and continuity, and possibly a repair manual for specific wiring diagrams.
Discuss the causes and fixes for B1B28 Jeep OBDII Code
Code B1B28 Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
