B1B0E Jeep Code - Passenger Airbag Squib 2 Circuit Open
Quick Answer
When powered, the Occupant Restraint Controller (ORC) sends a test current to the squibs to verify the integrity of the squib and wiring. Common causes include Faulty Passenger Airbag Squib 2, Passenger Airbag Squib 2 harness is open or shorted, Passenger Airbag Squib 2 circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1B0E Jeep indicates Passenger Airbag Squib 2 Circuit Open.
- Common causes
- Common causes include Faulty Passenger Airbag Squib 2, Passenger Airbag Squib 2 harness is open or shorted, Passenger Airbag Squib 2 circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B1B0E Jeep Description
What are the Possible Causes of the DTC B1B0E Jeep?
- Faulty Passenger Airbag Squib 2
- Passenger Airbag Squib 2 harness is open or shorted
- Passenger Airbag Squib 2 circuit poor electrical connection
- Faulty Passenger Airbag
- Faulty Occupant Restraint Controller (ORC)
How to Fix the DTC B1B0E Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B1B0E Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B1B0E Jeep code?
Need more information on how to fix the B1B0E Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1B0E Jeep code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1B0E Jeep Code
1. What does OBDII code B1B0E mean for a Jeep?
B1B0E indicates an open circuit in the passenger airbag squib 2, which is part of the airbag system responsible for deploying the passenger airbag in a collision.
2. What are the common symptoms of code B1B0E in a Jeep?
The most common symptoms include the airbag warning light illuminating on the dashboard and the potential deactivation of the passenger airbag.
3. Can I still drive my Jeep with code B1B0E?
While the vehicle is drivable, the passenger airbag may not deploy in the event of a collision, posing a safety risk.
4. What causes the B1B0E code to appear in a Jeep?
Common causes include damaged wiring, a faulty airbag module, a bad clock spring, or loose or corroded electrical connections in the airbag system.
5. How can I diagnose the B1B0E code in my Jeep?
Start by scanning the vehicle with an OBDII tool, inspecting the passenger airbag wiring and connectors for damage, and testing the clock spring and airbag module for faults.
6. How do I fix code B1B0E on a Jeep?
Repairs may involve repairing or replacing damaged wiring, tightening loose connections, replacing the clock spring, or replacing a faulty airbag module.
7. Is code B1B0E covered under warranty for my Jeep?
Airbag systems are often covered under extended safety warranties, but coverage depends on the vehicle’s age and warranty terms. Check with your dealership.
8. Can a faulty clock spring cause the B1B0E code?
Yes, a faulty clock spring can prevent proper electrical connection to the passenger airbag, triggering the B1B0E code.
9. Do I need to reset the airbag system after fixing code B1B0E?
Yes, after repairs, clear the code with an OBDII scanner and ensure the airbag system is functioning properly.
10. Should I attempt to repair code B1B0E myself?
Airbag system repairs can be dangerous due to the risk of accidental deployment. It’s recommended to have a professional handle the diagnosis and repair.
Discuss the causes and fixes for B1B0E Jeep OBDII Code
Code B1B0E Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
