AutoCodes – Jeep – B1B06 Jeep

B1B06 Jeep Code - Driver Airbag Squib 2 Circuit Open

Quick Answer

When powered, the Occupant Restraint Controller (ORC) sends a test current to the squibs to verify the integrity of the squib and wiring. Common causes include Faulty Driver Airbag Squib 2, Driver Airbag Squib 2 harness is open or shorted, Driver Airbag Squib 2 circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B1B06 Jeep indicates Driver Airbag Squib 2 Circuit Open.
Common causes: Common causes include Faulty Driver Airbag Squib 2, Driver Airbag Squib 2 harness is open or shorted, Driver Airbag Squib 2 circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 23,129

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Aug 14, 2019

Description
Possible Causes
How To Fix
Tech Notes ▶
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B1B06 Jeep Description

When powered, the Occupant Restraint Controller (ORC) sends a test current to the squibs to verify the integrity of the squib and wiring. These circuits are maintained in a "floating" configuration at the module (connected to neither power nor ground) as protection against inadvertent deployment. The use of the SRS Load Tool Adaptor provides a test point as well as a method for opening the shorting bar connections within the harness connector. The Clockspring is part of the Steering Column Control Module (SCCM). The SCCM includes the steering column shroud, the Steering Angle Sensor (SAS), the Clockspring, the Multi-function Switch, a Steering Column Power Tilt and Telescope Switch (if equipped), and a trim cover. The SCCM is replaced as an entire assembly. The ORC sends out a 40 mA diagnostic current on each squib voltage supply circuit at power up and every 500 ms thereafter while the ignition is on.

OBDII Code B1B06 Jeep - Driver Airbag Squib 2 Circuit Open - AutoCodes.com — B1B06 Jeep Code - Driver Airbag Squib 2 Circuit Open

What does this mean?

What are the Possible Causes of the DTC B1B06 Jeep?

Faulty Driver Airbag Squib 2
Driver Airbag Squib 2 harness is open or shorted
Driver Airbag Squib 2 circuit poor electrical connection
Faulty Driver Airbag
Faulty Steering Comun Control Module (Clockspring)
Faulty Occupant Restraint Controller (ORC)

How to Fix the DTC B1B06 Jeep?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

User Submitted Video

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B1B06 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B1B06 Jeep code?

Need more information on how to fix the B1B06 Jeep code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1B06 Jeep code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B1B06 Jeep Code

1. What are the common symptoms of OBDII code B1B06 in a Jeep related to the Driver Airbag Squib 2 Circuit Open?

- Common symptoms include the airbag warning light staying illuminated on the dashboard and the airbag system being disabled.

2. What causes the OBDII code B1B06 in a Jeep, indicating a Driver Airbag Squib 2 Circuit Open?

- The code B1B06 is typically triggered by a fault in the wiring or connections to the driver airbag squib 2, which is the electrical component responsible for deploying the airbag.

3. How serious is the OBDII code B1B06 in a Jeep indicating a Driver Airbag Squib 2 Circuit Open?

- This code indicates a potentially serious safety issue as it relates to the driver's airbag functionality. It is crucial to address this problem promptly to ensure the airbag system operates correctly in the event of a collision.

4. Can I continue driving my Jeep with the OBDII code B1B06 related to the Driver Airbag Squib 2 Circuit Open?

- It is not recommended to drive the vehicle with this code present, as the driver's airbag may not deploy in an accident. Have the issue diagnosed and repaired by a qualified technician as soon as possible.

5. How can I diagnose and repair the OBDII code B1B06 in my Jeep indicating a Driver Airbag Squib 2 Circuit Open?

- Diagnosis involves inspecting the wiring and connections to the driver airbag squib 2 for any damage or loose connections. Repair typically involves repairing or replacing the faulty wiring or connector.

6. Are there any safety precautions to take when working on the driver airbag system to address the OBDII code B1B06 in a Jeep?

- It is crucial to disconnect the vehicle's battery and wait for at least 15 minutes before working on the airbag system to prevent accidental deployment, which can cause injury.

7. Can resetting the OBDII code B1B06 related to the Driver Airbag Squib 2 Circuit Open fix the issue in my Jeep?

- Resetting the code may temporarily turn off the warning light, but it will not fix the underlying problem causing the circuit open fault. The issue should be properly diagnosed and repaired.

8. Is it possible to clear the OBDII code B1B06 in my Jeep indicating a Driver Airbag Squib 2 Circuit Open without fixing the problem?

- While it is possible to clear the code using an OBDII scanner, the underlying issue causing the fault must be addressed to ensure the airbag system functions correctly.

9. How much does it typically cost to repair the OBDII code B1B06 related to the Driver Airbag Squib 2 Circuit Open in a Jeep?

- The cost of repairing this code can vary depending on the specific cause of the fault and the labor rates in your area. It is recommended to obtain a diagnosis from a qualified technician for an accurate estimate.

10. Can a DIY enthusiast with automotive experience fix the OBDII code B1B06 indicating a Driver Airbag Squib 2 Circuit Open in a Jeep?

- While some DIY enthusiasts may have the skills to diagnose and repair wiring issues, working on the airbag system requires caution and specific knowledge. It is generally recommended to have this type of repair done by a professional technician.