B1A02 Lincoln Code - Speaker 2 General Electric Failure
Quick Answer
The Audio Control Module (ACM) directs audio signals to the audio amplifier and to the subwoofer amplifier in the form of an AC voltage. Common causes include Blown Audio Fuse, Faulty Speaker, Speaker harness is open or shorted. Severity is Low - monitor the vehicle and repair when practical. The vehicle can usually be driven if no severe symptoms are present, but symptoms should be checked before extended driving.
- What it means
- B1A02 Lincoln indicates Speaker 2 General Electric Failure.
- Common causes
- Common causes include Blown Audio Fuse, Faulty Speaker, Speaker harness is open or shorted.
- Severity
- Low - monitor the vehicle and repair when practical.
- Can I drive?
- The vehicle can usually be driven if no severe symptoms are present, but symptoms should be checked before extended driving.
Code B1A02 Lincoln Description
A short to ground or short to voltage in the circuitry to one of the speakers may cause multiple speakers to lose sound due to the built-in overload protection feature of the ACM. In this case, a speaker fault DTC sets, and this pinpoint test should be followed to isolate the damaged circuit.
To enable the amplifiers, the ACM sends voltage through individual enable/clip circuits. The circuits act as both an output (to enable the amplifier) and an input (to detect an overload condition). The voltage sent by the ACM passes through a variable resistor in each amplifier, then to ground. As the amplifier reaches maximum output, the resistance in the variable resistor decreases. This decreases the voltage drop, resulting in the ACM detecting a higher voltage on the enable/clip circuit. When the voltage reaches the clip threshold, the ACM clips the audio output signal to the amplifier (heard as distortion), in order to prevent damage to the amplifier and speakers.
The enable/clip status is based on the following voltages, as detected by the ACM:
- Less than 0.4 volts: amplifier disabled
- Between 3.8 and 6.7 volts (nominal): amplifier enabled
- Greater than 8.5 volts: amplifier clipped
An open in the enable/clip circuit causes the speakers powered by that particular amplifier to produce no sound because the enable signal does not reach the audio amplifier. A short to ground or short to voltage can cause severe distortion to be heard in the speakers.
What are the Possible Causes of the DTC B1A02 Lincoln?
- Blown Audio Fuse
- Faulty Speaker
- Speaker harness is open or shorted
- Speaker circuit poor electrical connection
- Faulty Audio amplifier
- Faulty Subwoofer amplifier
- Faulty Audio Control Module (ACM)
How to Fix the DTC B1A02 Lincoln?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
B1A02:11 Speaker #2 Circuit Short to Ground
B1A02:12 Speaker #2 Circuit Short to Battery
B1A02:13 Speaker #2 Circuit Open
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B1A02 Lincoln code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B1A02 Lincoln code?
Need more information on how to fix the B1A02 Lincoln code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1A02 Lincoln code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about B1A02 Lincoln Code
What does OBDII code B1A02 mean for my Lincoln?
OBDII code B1A02 indicates a "Speaker 2 General Electric Failure," which typically points to an issue with the second speaker in the vehicle's audio system.
What symptoms might I experience with code B1A02?
Common symptoms include poor audio quality, no sound from the second speaker, or the entire audio system malfunctioning.
What could cause the B1A02 code to trigger?
Causes may include a faulty speaker, damaged wiring, a malfunctioning amplifier, or issues with the vehicle's audio system control module.
How can I determine if the speaker is actually faulty?
You can perform a visual inspection for damaged wires and connections, and test the speaker with a multimeter to check for continuity.
Are there any DIY repair tips for fixing code B1A02?
Check and repair any damaged wiring, securely reconnect any loose connections, and consider replacing the faulty speaker if testing confirms it's defective.
Is it safe to drive my Lincoln with the B1A02 code active?
While it may not affect the vehicle's drivability, it is advisable to address the issue to restore audio functionality and avoid potential electrical problems.
Can I clear the B1A02 code myself?
Yes, you can use an OBDII scanner to clear the code, but if the underlying issue isn't resolved, the code may reappear.
Should I consult a professional if I can't find the issue?
If you're unable to diagnose or fix the problem after basic troubleshooting, it's best to consult a professional mechanic or an audio specialist for further assistance.
Will fixing the B1A02 code improve my vehicle's resale value?
Restoring the audio system functionality and addressing any error codes can enhance your vehicle's appeal and potentially improve its resale value.
Discuss the causes and fixes for B1A02 Lincoln OBDII Code
Code B1A02 Lincoln comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
