B1692 2013 Toyota RAV4 Code - Lost Communication with Door Side Airbag Sensor Right
Quick Answer
The circuit for the Side Collision Sensor Right (RH) is composed of the Center Airbag Sensor, Side Airbag Sensor Right, and Rear Airbag Sensor Right. Common causes include Faulty Side Airbag Sensor Right (RH), Side Airbag Sensor Right harness is open or shorted, Side Airbag Sensor Right circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1692 2013 Toyota RAV4 indicates Lost Communication with Door Side Airbag Sensor Right.
- Common causes
- Common causes include Faulty Side Airbag Sensor Right (RH), Side Airbag Sensor Right harness is open or shorted, Side Airbag Sensor Right circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B1692 2013 Toyota RAV4 Description
What are the Possible Causes of the DTC B1692 2013 Toyota RAV4?
- Faulty Side Airbag Sensor Right (RH)
- Side Airbag Sensor Right harness is open or shorted
- Side Airbag Sensor Right circuit poor electrical connection
- Faulty Center Airbag Sensor Assembly
How to Fix the DTC B1692 2013 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B1692 2013 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B1692 2013 Toyota RAV4 code?
Need more information on how to fix the B1692 2013 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1692 2013 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1692 2013 Toyota RAV4 Code
1. What does OBDII code B1692 mean in a 2013 Toyota RAV4?
Code B1692 indicates a loss of communication with the right-side door airbag sensor, which may affect the proper deployment of the airbag system.
2. What are the symptoms of code B1692 in a 2013 Toyota RAV4?
Common symptoms include an illuminated airbag warning light and potential malfunction of the right-side airbag system.
3. What causes code B1692 in a 2013 Toyota RAV4?
The code can be triggered by a faulty door airbag sensor, damaged wiring or connectors, or an issue with the airbag control module.
4. Can I still drive my 2013 Toyota RAV4 with code B1692 active?
While the vehicle may drive normally, the airbag system may not function properly in an accident, posing a serious safety risk.
5. How do I diagnose code B1692 in a 2013 Toyota RAV4?
Start by checking the wiring and connectors for the right-side door airbag sensor for damage or corrosion. Use a diagnostic scan tool to confirm communication with the sensor.
6. How do I repair code B1692 on a 2013 Toyota RAV4?
Repairs may involve replacing a faulty door airbag sensor, repairing damaged wiring, or reprogramming or replacing the airbag control module if necessary.
7. Can a dead battery cause code B1692 in a 2013 Toyota RAV4?
A weak or dead battery can sometimes cause communication issues, but it’s more commonly related to wiring or sensor faults.
8. How much does it cost to fix code B1692 in a 2013 Toyota RAV4?
Repair costs vary but typically range from $100 to $300 for wiring repairs and up to $500 or more for sensor or module replacement.
9. Can I clear code B1692 without fixing the issue?
Clearing the code without addressing the problem will likely result in the code returning and the airbag warning light staying on.
10. Is code B1692 a common issue in the 2013 Toyota RAV4?
While not extremely common, communication issues with airbag sensors can occur due to wear, corrosion, or impact damage over time.
Discuss the causes and fixes for B1692 2013 Toyota RAV4 OBDII Code
Code B1692 2013 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
