AutoCodes.com | All About OBDII Engine Codes
AutoCodes - Scion - B1661 Scion

B1661 Scion Code - Roll Over Cut Off Indicator Malfunction

- Code Popularity: 636 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
Share on Facebook   Share on Twitter   Share on Linkedin

What are the Possible Causes of the DTC B1661 Scion?

NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
  • Faulty Combination Meter Assembly
  • Faulty Curtain Shield Airbag Cutoff Switch
  • Combination Meter Assembly harness is open or shorted
  • Combination Meter Assembly circuit poor electrical connection
  • Faulty Center Airbag Sensor
⚠ Does your Scion have Safety Recalls? → Check here

How to Fix the DTC B1661 Scion?

Review the 'Possible Causes' mentioned above and visually examine the corresponding wiring harness and connectors. Ensure to check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.

Search for B1661 Scion Questions and Answers: Search here →

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B1661 Scion code, it typically requires 1.0 hour of labor. The specific diagnosis time and labor rates at auto repair shops can differ based on factors such as the location, make and model of the vehicle, and even the engine type. It is common for most auto repair shops to charge between $75 and $150 per hour.

What are Code Possible Symptoms?

  • Air Bag Warning Light ON

Code B1661 Scion Description

The Curtain Shield Airbag Cutoff Switch is a mechanism that operates both the right and left sides of the Curtain Shield Airbag and the Front Seat Outer Belt when the Center Airbag Sensor detects a roll-over. The Roll Sensing Curtain Airbag (RSCA) OFF indicator is installed in the Combination Meter. If the Curtain Shield Airbag Cutoff Switch is operated, the indicator comes on to inform the drive that the roll-over detection system is not working. The initial setting of the roll-over detection system is on. It automatically operates every time the engine switch is turned on (IG).

OBDII Code B1661 Scion - Roll Over Cut Off Indicator Malfunction - AutoCodes.com
B1661 Scion Code - Roll Over Cut Off Indicator Malfunction

Need More Information on the Code?

Need more information on how to fix the B1661 Scion code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1661 Scion code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

Code B1661 Scion comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the B1661 Scion code? Have you replaced any parts?
Any information is appreciated. Thanks