B1362 Chevrolet Code - Driver Belt Pretensioner Resistance Too High
Quick Answer
When the ignition switch is turned to ON, the Sensing and Diagnostic Module (SDM) will perform turn-on test to diagnose critical malfunctions within SDM itself. Common causes include Faulty Driver Belt Pretensioner, Driver Belt Pretensioner harness is open or shorted, Driver Belt Pretensioner circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1362 Chevrolet indicates Driver Belt Pretensioner Resistance Too High.
- Common causes
- Common causes include Faulty Driver Belt Pretensioner, Driver Belt Pretensioner harness is open or shorted, Driver Belt Pretensioner circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B1362 Chevrolet Description
Upon passing these test ignition and deployment loop voltages are measured to ensure that they are within their normal voltage ranges. The SDM monitors the voltages at the driver low and the passenger low to detect shorts to ground or voltage in the deploy loops.
The SDM checks the wiring connection to the driver belt pretensioner by letting the infinitesimal current flow through the internal circuit and verify the resistance.
What are the Possible Causes of the DTC B1362 Chevrolet?
- Faulty Driver Belt Pretensioner
- Driver Belt Pretensioner harness is open or shorted
- Driver Belt Pretensioner circuit poor electrical connection
How to Fix the DTC B1362 Chevrolet?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B1362 Chevrolet code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B1362 Chevrolet code?
Need more information on how to fix the B1362 Chevrolet code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1362 Chevrolet code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1362 Chevrolet Code
1. What are the common symptoms of OBDII code B1362 in a Chevrolet related to the driver belt pretensioner resistance being too high?
The common symptoms include the airbag warning light illuminating on the dashboard, a chime or alert indicating an issue with the driver's seatbelt pretensioner system, and potential issues with the deployment of the seatbelt in the event of a collision.
2. What could cause the OBDII code B1362 in a Chevrolet indicating that the driver belt pretensioner resistance is too high?
The code B1362 typically indicates a fault with the driver's seatbelt pretensioner system, which can be caused by a faulty seatbelt pretensioner, damaged wiring or connectors in the system, or a malfunctioning airbag control module.
3. How can I troubleshoot and diagnose the OBDII code B1362 in a Chevrolet related to the driver belt pretensioner resistance being too high?
To diagnose the issue, you can start by inspecting the seatbelt pretensioner and its wiring for any visible damage. Using a multimeter, you can test the resistance of the pretensioner to determine if it falls outside the acceptable range specified by the manufacturer.
4. Can I continue driving my Chevrolet if OBDII code B1362 is triggered due to high resistance in the driver belt pretensioner?
It is not recommended to continue driving the vehicle with an active B1362 code, as it indicates a potential safety issue with the seatbelt pretensioner system. It is best to address the problem promptly to ensure the proper functioning of the safety features in your vehicle.
5. How can I repair OBDII code B1362 in a Chevrolet caused by high resistance in the driver belt pretensioner?
Repairing the B1362 code may involve replacing the faulty driver's seatbelt pretensioner, repairing or replacing damaged wiring or connectors in the system, or resetting the airbag control module after addressing the underlying issue.
6. Is it safe to reset the OBDII code B1362 in a Chevrolet without addressing the root cause of the high resistance in the driver belt pretensioner?
Resetting the code without addressing the underlying issue is not recommended, as it may temporarily clear the warning light but will not solve the safety concern related to the driver's seatbelt pretensioner system. It is crucial to diagnose and repair the root cause of the problem.
7. How much does it typically cost to repair OBDII code B1362 in a Chevrolet due to high resistance in the driver belt pretensioner?
The cost of repairing the B1362 code can vary depending on the specific cause of the issue, the labor rates in your area, and whether any parts need to be replaced. It is advisable to consult a professional mechanic for an accurate diagnosis and cost estimate.
8. Are there any preventive maintenance tips to avoid triggering OBDII code B1362 in a Chevrolet related to the driver belt pretensioner resistance being too high?
Regularly inspecting the seatbelt pretensioner system for any signs of wear or damage, avoiding excessive pulling or tugging on the seatbelt, and promptly addressing any airbag warning lights on the dashboard can help prevent issues that may trigger the B1362 code.
9. Can a DIY enthusiast with automotive knowledge repair OBDII code B1362 in a Chevrolet caused by high resistance in the driver belt pretensioner?
While some DIY enthusiasts may have the skills to diagnose and repair issues related to the driver's seatbelt pretensioner system, it is recommended to consult a professional mechanic for complex safety-related concerns like the B1362 code to ensure proper diagnosis and repair.
10. Will clearing the OBDII code B1362 in a Chevrolet reset all other stored fault codes in the vehicle's system?
Clearing the B1362 code will only reset that specific fault code related to the driver belt pretensioner resistance being too high. Other stored fault codes in different systems of the vehicle will remain unaffected and may require individual diagnosis and repair if necessary.
Discuss the causes and fixes for B1362 Chevrolet OBDII Code
Code B1362 Chevrolet comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
