B11D6 Mercury Code - Driver Display Alert LED
Quick Answer
On each ignition cycle, the Side Obstacle Detection Control Module - Right (SOD-R) and Side Obstacle Detection Control Module - Left (SOD-L) run a self diagnostic check during which the exterior mirror Blind Spot Information System (BLIS™)/Cross Traffic Alert (CTA) LEDs illuminate for 3 seconds then turn off indicating the system is operational. Common causes include Faulty Driver Display Alert LED, Driver Display Alert LED harness is open or shorted, Driver Display Alert LED circuit poor electrical connection. Severity is Low - monitor the vehicle and repair when practical. The vehicle can usually be driven if no severe symptoms are present, but symptoms should be checked before extended driving.
- What it means
- B11D6 Mercury indicates Driver Display Alert LED.
- Common causes
- Common causes include Faulty Driver Display Alert LED, Driver Display Alert LED harness is open or shorted, Driver Display Alert LED circuit poor electrical connection.
- Severity
- Low - monitor the vehicle and repair when practical.
- Can I drive?
- The vehicle can usually be driven if no severe symptoms are present, but symptoms should be checked before extended driving.
Code B11D6 Mercury Description
What are the Possible Causes of the DTC B11D6 Mercury?
- Faulty Driver Display Alert LED
- Driver Display Alert LED harness is open or shorted
- Driver Display Alert LED circuit poor electrical connection
How to Fix the DTC B11D6 Mercury?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
B11D6:15 Driver Display Alert LED: Circuit Short To Battery or open
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B11D6 Mercury code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B11D6 Mercury code?
Need more information on how to fix the B11D6 Mercury code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B11D6 Mercury code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about B11D6 Mercury Code
1. What does the OBDII code B11D6 for Mercury Driver Display Alert LED indicate?
- The code B11D6 indicates a fault with the Driver Display Alert LED in a Mercury vehicle.
2. What are the common symptoms of a B11D6 OBDII code on a Mercury?
- Common symptoms include the Driver Display Alert LED not functioning properly or displaying incorrect information.
3. What are the potential causes of a B11D6 OBDII code in a Mercury?
- Possible causes include a faulty Driver Display Alert LED, wiring issues, or a problem with the vehicle's electronic control unit (ECU).
4. How can I diagnose a B11D6 OBDII code related to the Driver Display Alert LED in my Mercury?
- To diagnose the issue, you can use an OBDII scanner to read the code and inspect the Driver Display Alert LED for any visible damage or irregularities.
5. Can I repair a B11D6 OBDII code on my Mercury myself?
- Depending on the cause, you may be able to repair the issue yourself by replacing the faulty Driver Display Alert LED or addressing any wiring problems.
6. Is it safe to continue driving my Mercury with a B11D6 OBDII code?
- It is generally safe to drive the vehicle with this code, but it is recommended to address the issue promptly to avoid potential safety hazards or further damage.
7. How much does it cost to fix a B11D6 OBDII code for the Driver Display Alert LED in a Mercury?
- The cost of repair can vary depending on the specific cause of the issue, but it may range from a few dollars for a simple LED replacement to a few hundred dollars for more complex repairs.
8. Can a B11D6 OBDII code in a Mercury be a recurring problem?
- If the underlying cause of the issue is not properly addressed during repair, the B11D6 code may reappear in the future.
9. Are there any troubleshooting tips for a B11D6 OBDII code on a Mercury?
- You can start by checking the LED connections, inspecting the wiring for any damage, and ensuring the ECU is functioning correctly to troubleshoot the issue.
10. Will resetting the OBDII system clear the B11D6 code in a Mercury?
- Resetting the OBDII system may temporarily clear the code, but it is essential to address the root cause of the problem to prevent it from reoccurring.
Discuss the causes and fixes for B11D6 Mercury OBDII Code
Code B11D6 Mercury comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
