AutoCodesGMC – B1019 2015 GMC Sierra

B1019 2015 GMC Sierra Code - SDM System Configuration Error

Quick Answer

The Inflatable Restraint Sensing and Diagnostic Module (SDM) monitors the number of safety components installed on the vehicle. Common causes include Program Inflatable Restraint Sensing and Diagnostic Module (SDM), Faulty Inflatable Restraint Sensing and Diagnostic Module, Inflatable Restraint Sensing and Diagnostic Module harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means
B1019 2015 GMC Sierra indicates SDM System Configuration Error.
Common causes
Common causes include Program Inflatable Restraint Sensing and Diagnostic Module (SDM), Faulty Inflatable Restraint Sensing and Diagnostic Module, Inflatable Restraint Sensing and Diagnostic Module harness is open or shorted.
Severity
High - diagnose this code as soon as possible.
Can I drive?
Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
AI answers can be wrong. Verify repairs with testing. Open full chat
Code Popularity 271
How popular is this code, among other codes? Low
Table of contents Created and updated by William Orellana on Apr 05, 2023
💬 Need more help? Ask Coddy for instant answers — it's free!

Code B1019 2015 GMC Sierra Description

The Inflatable Restraint Sensing and Diagnostic Module (SDM) monitors the number of safety components installed on the vehicle. When the ignition is turned ON, the Inflatable Restraint Sensing and Diagnostic Module evaluates the number of safety components installed and compares it to the number of components the Inflatable Restraint Sensing and Diagnostic Module expects to see on the vehicle with its current calibration. If there is a mismatch between the detected components and the components programmed with the Inflatable Restraint Sensing and Diagnostic Module calibration, Diagnostic Trouble Code (DTC) B1019 will be set. The components (if equipped) that the Inflatable Restraint Sensing and Diagnostic Module will detect include inflatable restraint deployment loops, impact sensors, passenger presence system components, seat position sensors, disable switches, and seat belt switches.
OBDII Code B1019 2015 GMC Sierra - SDM System Configuration Error - AutoCodes.com
B1019 2015 GMC Sierra Code - SDM System Configuration Error

What are the Possible Causes of the DTC B1019 2015 GMC Sierra?

  • Program Inflatable Restraint Sensing and Diagnostic Module (SDM)
  • Faulty Inflatable Restraint Sensing and Diagnostic Module
  • Inflatable Restraint Sensing and Diagnostic Module harness is open or shorted
  • Inflatable Restraint Sensing and Diagnostic Module circuit poor electrical connection

How to Fix the DTC B1019 2015 GMC Sierra?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

Code Tech Notes

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B1019 2015 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B1019 2015 GMC Sierra code?

Need more information on how to fix the B1019 2015 GMC Sierra code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1019 2015 GMC Sierra code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B1019 2015 GMC Sierra Code

1. What does the OBDII code B1019 mean on a 2015 GMC Sierra?

The code B1019 indicates a "SDM System Configuration Error," which typically points to a configuration mismatch or programming issue in the Supplemental Restraint System (SRS) module.

2. What are the common symptoms of the B1019 code on a 2015 GMC Sierra?

Symptoms may include the airbag warning light being illuminated, a chime or error message on the dashboard, and potential deactivation of the vehicle's airbag system.

3. What causes the B1019 code to appear on a 2015 GMC Sierra?

Common causes include incorrect programming of the SRS module, installation of an incompatible module, faulty wiring or connectors, or a module that has not been properly set up after replacement.

4. Is the airbag system affected when the B1019 code is active?

Yes, the airbag system may be disabled when this code is active, which could compromise occupant safety in the event of a collision.

5. How can I diagnose the B1019 code on my 2015 GMC Sierra?

Use an advanced scan tool to check for stored codes and verify the configuration of the SDM (Sensing and Diagnostic Module). Inspect related wiring and connectors for damage or corrosion.

6. Can the B1019 code be caused by a collision or airbag deployment?

Yes, the code can appear if the SDM was not properly reset or replaced after an airbag deployment or collision repair.

7. How do I fix the B1019 code on a 2015 GMC Sierra?

Repairs may involve reprogramming or recalibrating the SDM, ensuring the correct module is installed, or addressing wiring and connector issues if present.

8. Do I need a professional to fix the B1019 code?

Yes, resolving this issue often requires specialized diagnostic tools and expertise, so it's recommended to consult a certified technician or dealership.

9. Can I clear the B1019 code without fixing the issue?

Clearing the code without addressing the root cause will not solve the problem, and the code is likely to return. Additionally, the airbag system may remain inoperative.

10. What tools are needed to address the B1019 code on a 2015 GMC Sierra?

You’ll need an advanced scan tool capable of accessing the SRS module, along with software to reprogram or configure the SDM if necessary.

Discuss the causes and fixes for B1019 2015 GMC Sierra OBDII Code

Code B1019 2015 GMC Sierra comments

No comments found for this page.

AutoCodes App

Fix Your Car Smarter

Try the New AutoCodes App!

Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.

AutoCodes App on Google Play