AutoCodes – Chevrolet – B1001 2014 Chevrolet Silverado

B1001 2014 Chevrolet Silverado Code - SDM Option Configuration Error

Quick Answer

The Inflatable Restraint Sensing and Diagnostic Module (SDM) stores the vehicle's restraint ID from the Vehicle Identification Number (VIN) and the last 4 digits of the SDM part number. Common causes include Faulty Inflatable Restraint Sensing and Diagnostic Module (SDM), Faulty Passenger Presence System (PPS) (If equipped), Faulty Body Control Module (BCM). Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B1001 2014 Chevrolet Silverado indicates SDM Option Configuration Error.
Common causes: Common causes include Faulty Inflatable Restraint Sensing and Diagnostic Module (SDM), Faulty Passenger Presence System (PPS) (If equipped), Faulty Body Control Module (BCM).
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 516

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Apr 04, 2023

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B1001 2014 Chevrolet Silverado Description

The Inflatable Restraint Sensing and Diagnostic Module (SDM) stores the vehicle's restraint ID from the Vehicle Identification Number (VIN) and the last 4 digits of the SDM part number. When the ignition is turned ON, the SDM compares this information to the information stored in the Body Control Module (BCM) over the General Motors Local Area Network (GMLAN) communication circuit. If there is a mismatch between the information stored in the SDM and BCM, Diagnostic Trouble Code (DTC) B1001 will be set.

OBDII Code B1001 2014 Chevrolet Silverado - SDM Option Configuration Error - AutoCodes.com — B1001 2014 Chevrolet Silverado Code - SDM Option Configuration Error

What does this mean?

What are the Possible Causes of the DTC B1001 2014 Chevrolet Silverado?

Faulty Inflatable Restraint Sensing and Diagnostic Module (SDM)
Faulty Passenger Presence System (PPS) (If equipped)
Faulty Body Control Module (BCM)

How to Fix the DTC B1001 2014 Chevrolet Silverado?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

When the B1001 is set on a device other than the Inflatable Restraint Sensing and Diagnostic Module (SDM), it means that the device is not configured properly.

B1001:00 Option Configuration Error
B1001:45 Option Configuration Error Variant Not Programmed
B1001:46 Option Configuration Error Configuration Not Programmed
B1001:4B Option Configuration Error Calibration Not Learned

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B1001 2014 Chevrolet Silverado code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B1001 2014 Chevrolet Silverado code?

Need more information on how to fix the B1001 2014 Chevrolet Silverado code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1001 2014 Chevrolet Silverado code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B1001 2014 Chevrolet Silverado Code

1. What does the OBDII code B1001 for a 2014 Chevrolet Silverado indicate?

The B1001 code for a 2014 Chevrolet Silverado points to an SDM (Sensing and Diagnostic Module) Option Configuration Error.

2. What are the common symptoms of the SDM Option Configuration Error (B1001) in a 2014 Chevy Silverado?

Common symptoms of the B1001 code in a 2014 Silverado may include the airbag warning light staying on, non-deployment of airbags in a collision, and potential issues with the vehicle's safety systems.

3. What are the possible causes of the SDM Option Configuration Error (B1001) in a 2014 Chevy Silverado?

Causes of the B1001 code can include a faulty SDM module, wiring issues, a software glitch, or a recent repair or modification that affected the vehicle's safety systems.

4. How can I diagnose the SDM Option Configuration Error (B1001) in my 2014 Chevrolet Silverado?

Diagnosing the B1001 code typically involves using a professional OBDII scanner to read and interpret the code, checking the vehicle's wiring and connections, and inspecting the SDM module for any visible damage.

5. Can I continue driving my 2014 Chevy Silverado with the SDM Option Configuration Error (B1001) code?

It is not recommended to drive the vehicle with the B1001 code present, as it indicates a potential issue with the airbag system, which is crucial for occupant safety in the event of a collision.

6. How can I repair the SDM Option Configuration Error (B1001) in my 2014 Chevrolet Silverado?

Repairing the B1001 code may involve resetting the SDM module, checking and repairing any damaged wiring or connections, or replacing the SDM module if necessary.

7. Is it possible to reset the SDM module to clear the B1001 code on a 2014 Silverado?

Resetting the SDM module to clear the B1001 code may be possible in some cases, but it's important to diagnose the root cause of the error before attempting a reset to ensure the issue is fully resolved.

8. Are there any safety concerns associated with the SDM Option Configuration Error (B1001) in a 2014 Chevy Silverado?

Yes, there are safety concerns with the B1001 code, as it indicates a potential issue with the vehicle's airbag system, which could compromise occupant safety in the event of a collision.

9. Can a DIY enthusiast fix the SDM Option Configuration Error (B1001) in a 2014 Chevrolet Silverado?

While some basic troubleshooting steps can be taken by a DIY enthusiast, diagnosing and repairing the B1001 code may require professional expertise and specialized tools, especially when dealing with safety systems like the airbags.

10. How much can I expect to pay to repair the SDM Option Configuration Error (B1001) in my 2014 Chevy Silverado?

The cost of repairing the B1001 code can vary depending on the root cause of the issue, the extent of the repairs needed, and whether any parts need to be replaced. It is recommended to consult a professional mechanic for an accurate estimate.