B067A 2015 GMC Sierra Code - Rollover Protection OFF Indicator Circuit
Quick Answer
If the vehicle is equipped with a rollover protection disable switch, when pressed and held, will disable rollover protection and the inflatable restraint sensing and diagnostic module will illuminate the rollover protection disabled indicator. Common causes include Faulty Rollover Protection OFF Indicator, Rollover Protection OFF Indicator harness is open or shorted, Rollover Protection OFF Indicator circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B067A 2015 GMC Sierra indicates Rollover Protection OFF Indicator Circuit.
- Common causes
- Common causes include Faulty Rollover Protection OFF Indicator, Rollover Protection OFF Indicator harness is open or shorted, Rollover Protection OFF Indicator circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B067A 2015 GMC Sierra Description
What are the Possible Causes of the DTC B067A 2015 GMC Sierra?
- Faulty Rollover Protection OFF Indicator
- Rollover Protection OFF Indicator harness is open or shorted
- Rollover Protection OFF Indicator circuit poor electrical connection
- Faulty Inflatable Restraint Sensing and Diagnostic Module (SDM)
How to Fix the DTC B067A 2015 GMC Sierra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
B067A:02 Rollover Protection OFF Indicator Circuit Short to Ground
B067A:04 Rollover Protection OFF Indicator Circuit Open
B067A:05 Rollover Protection OFF Indicator Circuit High Voltage/Open
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B067A 2015 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B067A 2015 GMC Sierra code?
Need more information on how to fix the B067A 2015 GMC Sierra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B067A 2015 GMC Sierra code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B067A 2015 GMC Sierra Code
1. What does the OBDII code B067A mean on a 2015 GMC Sierra?
The code B067A indicates an issue with the Rollover Protection OFF Indicator Circuit, which controls the light or alert signaling the status of the rollover protection system.
2. What are common symptoms of code B067A on a 2015 GMC Sierra?
Symptoms may include the Rollover Protection OFF indicator not illuminating, staying on constantly, or erratic behavior of the indicator light.
3. What causes the OBDII code B067A to appear?
Possible causes include a malfunctioning Rollover Protection OFF indicator light, damaged wiring or connectors in the circuit, or a fault in the Body Control Module (BCM).
4. Can I drive my 2015 GMC Sierra with the B067A code?
Yes, you can drive the vehicle, but the rollover protection system may not function properly in an emergency situation, which could pose a safety risk.
5. How do I diagnose the B067A code on my GMC Sierra?
Diagnose the code by checking the Rollover Protection OFF indicator light, inspecting the wiring and connectors for damage, and using a diagnostic scanner to test the Body Control Module (BCM).
6. What tools are needed to fix the B067A code?
You may need a multimeter to test the circuit, a diagnostic scanner to clear codes, and basic tools to repair or replace wiring, connectors, or the indicator light.
7. How much does it cost to repair the B067A code on a 2015 GMC Sierra?
The cost varies depending on the issue, but replacing a faulty indicator light or repairing wiring typically costs $50–$200. BCM replacement costs can exceed $300.
8. Can a loose connection trigger the B067A code?
Yes, a loose or corroded connection in the Rollover Protection OFF indicator circuit can trigger this code.
9. Will resetting the code fix the problem?
Resetting the code may temporarily clear it, but if the underlying issue isn’t addressed, the code will likely return.
10. Should I take my GMC Sierra to a mechanic for the B067A code?
If you’re not comfortable diagnosing electrical issues or if the problem persists after basic checks, it’s best to consult a professional mechanic.
Discuss the causes and fixes for B067A 2015 GMC Sierra OBDII Code
Code B067A 2015 GMC Sierra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
