B067A:04 Code - Rollover Protection OFF Indicator Circuit Open
Quick Answer
If the vehicle is equipped with a rollover protection disable switch, when pressed and held, will disable rollover protection and the inflatable restraint sensing and diagnostic module will illuminate the rollover protection disabled indicator. Common causes include Faulty Rollover Protection OFF Indicator, Rollover Protection OFF Indicator harness is open or shorted, Rollover Protection OFF Indicator circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B067A:04 indicates Rollover Protection OFF Indicator Circuit Open.
- Common causes
- Common causes include Faulty Rollover Protection OFF Indicator, Rollover Protection OFF Indicator harness is open or shorted, Rollover Protection OFF Indicator circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B067A:04 Description
What are the Possible Causes of the DTC B067A:04?
- Faulty Rollover Protection OFF Indicator
- Rollover Protection OFF Indicator harness is open or shorted
- Rollover Protection OFF Indicator circuit poor electrical connection
- Faulty Inflatable Restraint Sensing and Diagnostic Module (SDM)
How to Fix the DTC B067A:04?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
B067A:02 Rollover Protection OFF Indicator Circuit Short to Ground
B067A:04 Rollover Protection OFF Indicator Circuit Open
B067A:05 Rollover Protection OFF Indicator Circuit High Voltage/Open
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B067A:04 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B067A:04 code?
Need more information on how to fix the B067A:04 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B067A:04 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B067A:04 Code
1. What does OBDII code B067A:04 mean?
Code B067A:04 indicates an open circuit in the Rollover Protection OFF Indicator Circuit, which is responsible for signaling the status of the rollover protection system.
2. What are the common symptoms of B067A:04?
Symptoms may include the Rollover Protection OFF indicator not illuminating, intermittent warning lights, or no visual confirmation of system status.
3. What causes the B067A:04 code to appear?
This code is typically caused by a damaged or disconnected wiring harness, a faulty indicator bulb or LED, or a defective control module.
4. Can I drive my vehicle with the B067A:04 code present?
Yes, you can typically drive the vehicle, but the rollover protection system may not function correctly, posing a safety risk in rollover scenarios.
5. How do I diagnose the B067A:04 code?
Start by inspecting the wiring and connectors for damage or corrosion, then test the Rollover Protection OFF indicator circuit and check for continuity.
6. How can I fix the B067A:04 code?
Repairs may involve replacing damaged wiring, connectors, or the indicator bulb. If the issue persists, the control module may require replacement or reprogramming.
7. Does the B067A:04 code reset automatically after repairs?
In most cases, you’ll need to clear the code using an OBDII scanner after completing repairs to ensure it doesn’t reappear.
8. How much does it cost to repair the B067A:04 code?
Repair costs vary depending on the issue but typically range from $50 to $300 for parts and labor, excluding control module replacement.
9. Can a weak battery cause the B067A:04 code?
Yes, a weak or failing battery can sometimes lead to voltage-related issues that trigger this code.
10. What tools are needed to troubleshoot the B067A:04 code?
You’ll need an OBDII scanner, a multimeter for testing circuits, and basic hand tools for inspecting and repairing wiring or components.
Discuss the causes and fixes for B067A:04 OBDII Code
Code B067A:04 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
