B0100 GMC Code - Driver-Side EFS Valid Identification Not Received
Quick Answer
Electronic Frontal Sensor (EFS), also known as a front end sensor, uses a unidirectional 2-wire circuit. Common causes include Faulty Driver-Side Electronic Frontal Sensor (EFS), Driver-Side Electronic Frontal Sensor (EFS) harness is open or shorted, Driver-Side Electronic Frontal Sensor (EFS) circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B0100 GMC indicates Driver-Side EFS Valid Identification Not Received.
- Common causes
- Common causes include Faulty Driver-Side Electronic Frontal Sensor (EFS), Driver-Side Electronic Frontal Sensor (EFS) harness is open or shorted, Driver-Side Electronic Frontal Sensor (EFS) circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B0100 GMC Description
What are the Possible Causes of the DTC B0100 GMC?
- Faulty Driver-Side Electronic Frontal Sensor (EFS)
- Driver-Side Electronic Frontal Sensor (EFS) harness is open or shorted
- Driver-Side Electronic Frontal Sensor (EFS) circuit poor electrical connection
- Faulty Sensing and Diagnostic Module (SDM)
How to Fix the DTC B0100 GMC?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B0100 GMC code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B0100 GMC code?
Need more information on how to fix the B0100 GMC code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B0100 GMC code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B0100 GMC Code
1. What are the common symptoms of OBDII code B0100 GMC (Driver-Side EFS Valid Identification Not Received)?
- Common symptoms include the airbag warning light illuminating on the dashboard and potential loss of function of the driver-side airbag.
2. What are some possible causes of OBDII code B0100 GMC?
- Possible causes include a faulty electronic front sensor (EFS), wiring issues, or a problem with the airbag control module.
3. How can I diagnose the issue related to code B0100 GMC?
- A professional diagnostic scan tool can help pinpoint the exact cause of the problem by reading the codes stored in the airbag system.
4. Is it safe to drive with OBDII code B0100 GMC present?
- It is not recommended to drive with an active airbag fault code, as it may compromise the effectiveness of the airbag system in the event of a collision.
5. Can I reset the OBDII code B0100 GMC on my own?
- While you can clear the code with an OBDII scanner, it is important to address the underlying issue causing the fault code to prevent it from reoccurring.
6. What are some repair tips for resolving OBDII code B0100 GMC?
- Check all wiring connections related to the airbag system, inspect the EFS, and ensure the airbag control module is functioning properly.
7. How much does it typically cost to repair OBDII code B0100 GMC?
- Repair costs can vary depending on the specific cause of the issue, but typically range from $100 to $500, including parts and labor.
8. Will disconnecting the battery reset OBDII code B0100 GMC?
- Disconnecting the battery may clear the code temporarily, but it is recommended to address the underlying issue and perform a proper repair to prevent the code from returning.
9. Can I drive my vehicle for an extended period with OBDII code B0100 GMC without fixing it?
- It is not advisable to drive with an unresolved airbag system fault, as it may compromise the safety of the vehicle occupants in the event of a collision.
10. How long does it take to repair OBDII code B0100 GMC?
- The repair time can vary depending on the specific cause of the issue and the availability of parts, but most repairs can be completed within a few hours to a day.
Discuss the causes and fixes for B0100 GMC OBDII Code
-
What model and year is your vehicle? any other codes besides the B0100? The B0100 code is for the air bag system
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
