AutoCodes – Cadillac – B0100 Cadillac

B0100 Cadillac Code - Driver-Side EFS Valid Identification Not Received

Quick Answer

Electronic Frontal Sensor (EFS), also known as a front end sensor, uses a unidirectional 2-wire circuit. Common causes include Faulty Driver-Side Electronic Frontal Sensor (EFS), Driver-Side Electronic Frontal Sensor (EFS) harness is open or shorted, Driver-Side Electronic Frontal Sensor (EFS) circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B0100 Cadillac indicates Driver-Side EFS Valid Identification Not Received.
Common causes: Common causes include Faulty Driver-Side Electronic Frontal Sensor (EFS), Driver-Side Electronic Frontal Sensor (EFS) harness is open or shorted, Driver-Side Electronic Frontal Sensor (EFS) circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 4,023

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Jun 14, 2020

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B0100 Cadillac Description

Electronic Frontal Sensor (EFS), also known as a front end sensor, uses a unidirectional 2-wire circuit. EFS sensor modulates current on the interface to send identification, State Of Health (SOH) and deployment commands to Sensing and Diagnostic Module (SDM). The SDM serves as a power source and ground for EFS. When ignition is turned on and EFS detects power from SDM, EFS responds by performing internal diagnostics and sending identification to SDM. SDM considers identification message to be valid if received within 5 seconds of EFS powering up. EFS continually communicates a status message to SDM. When fault is detected, SDM will attempt to reset EFS twice by removing and applying power. If fault is still present, SDM will set a Diagnostic Trouble Code (DTC).

OBDII Code B0100 Cadillac - Driver-Side EFS Valid Identification Not Received - AutoCodes.com — B0100 Cadillac Code - Driver-Side EFS Valid Identification Not Received

What does this mean?

What are the Possible Causes of the DTC B0100 Cadillac?

Faulty Driver-Side Electronic Frontal Sensor (EFS)
Driver-Side Electronic Frontal Sensor (EFS) harness is open or shorted
Driver-Side Electronic Frontal Sensor (EFS) circuit poor electrical connection
Faulty Sensing and Diagnostic Module (SDM)

How to Fix the DTC B0100 Cadillac?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B0100 Cadillac code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B0100 Cadillac code?

Need more information on how to fix the B0100 Cadillac code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B0100 Cadillac code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B0100 Cadillac Code

1. What are the common symptoms of OBDII code B0100 in a Cadillac related to "Driver-Side EFS Valid Identification Not Received"?

- Common symptoms include the airbag warning light staying illuminated on the dashboard and potential loss of function of the driver-side airbag.

2. What could be the possible causes of OBDII code B0100 in a Cadillac?

- Possible causes may include a malfunctioning electronic front sensor (EFS), damaged wiring in the airbag system, or a faulty airbag control module.

3. How can I diagnose the issue causing OBDII code B0100 in my Cadillac?

- Diagnosis typically involves using a diagnostic scanner to retrieve the specific trouble code, inspecting the wiring and connections in the airbag system, and testing the components for proper functionality.

4. Is it safe to drive my Cadillac with OBDII code B0100 present?

- It is not recommended to drive the vehicle with the airbag warning light on, as it indicates a potential issue with the airbag system that could affect its proper deployment in the event of a collision.

5. Can I repair OBDII code B0100 in my Cadillac at home?

- While some DIY enthusiasts may attempt to address the issue, working on the airbag system can be complex and dangerous. It is advisable to have the problem diagnosed and repaired by a qualified technician to ensure safety and proper functionality.

6. How much does it typically cost to repair OBDII code B0100 in a Cadillac?

- The cost of repair can vary depending on the exact cause of the issue. It may involve replacing a faulty sensor, repairing damaged wiring, or reprogramming the airbag control module. Costs can range from a few hundred to over a thousand dollars.

7. Are there any recalls or service bulletins related to OBDII code B0100 in Cadillac vehicles?

- It is advisable to check with a Cadillac dealership or the manufacturer's website to see if there are any recalls or service bulletins addressing the specific issue related to OBDII code B0100 in your vehicle.

8. Will resetting the OBDII code B0100 in my Cadillac make the problem go away?

- Simply resetting the trouble code may temporarily turn off the warning light, but the underlying issue will persist. It is important to diagnose and address the root cause of the problem to ensure the airbag system functions properly.

9. Can OBDII code B0100 in a Cadillac affect the vehicle's overall safety?

- Yes, OBDII code B0100 indicates a potential problem with the driver-side airbag system, which can compromise the vehicle's safety in the event of a collision. It is crucial to address the issue promptly to ensure the airbags deploy as intended.

10. How long does it take to repair OBDII code B0100 in a Cadillac?

- The repair time can vary depending on the exact cause of the issue and the availability of parts. In general, diagnosing and repairing OBDII code B0100 may take a few hours to a full day at a repair shop.