AutoCodes – Ford – B007F Ford

B007F Ford Code - Passenger Seatbelt Pretensioner 'C' Deployment Control

Quick Answer

The Restraints Control Module (RCM) analyzes the deployment loop resistance to determine if a fault exists. Common causes include Faulty Passenger Seatbelt Pretensioner, Passenger Seatbelt Pretensioner harness is open or shorted, Passenger Seatbelt Pretensioner circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B007F Ford indicates Passenger Seatbelt Pretensioner 'C' Deployment Control.
Common causes: Common causes include Faulty Passenger Seatbelt Pretensioner, Passenger Seatbelt Pretensioner harness is open or shorted, Passenger Seatbelt Pretensioner circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 15,369

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Jun 14, 2020

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B007F Ford Description

The Restraints Control Module (RCM) analyzes the deployment loop resistance to determine if a fault exists. The value displayed in the PID is the deployment loop resistance measured by the RCM. If the value displayed is lower or higher than the desired range, the RCM can set a Diagnostic Trouble Code (DTC). As the deployment loop resistance drifts farther outside the desired range, the chance for a DTC increases. Small variations in resistance can occur due to the effect of road vibrations on terminal fit. Crimps and terminals can be affected by stress and harness movement and can cause an increase in resistance due to wire strain. These variables can result in an intermittent fault. For this reason, the test requires the PID value to be within the desired range before the fault is considered repaired, regardless if the module is reporting an on-demand DTC at the time of diagnosis. Following this direction helps make sure that minor changes in resistance do not create a repeat concern. This test uses the process of elimination to diagnose each part of the deployment loop circuit including:
- Wiring
- Connections
- Driver seatbelt anchor pretensioner
- RCM

OBDII Code B007F Ford - Passenger Seatbelt Pretensioner 'C' Deployment Control - AutoCodes.com — B007F Ford Code - Passenger Seatbelt Pretensioner 'C' Deployment Control

What does this mean?

What are the Possible Causes of the DTC B007F Ford?

Faulty Passenger Seatbelt Pretensioner
Passenger Seatbelt Pretensioner harness is open or shorted
Passenger Seatbelt Pretensioner circuit poor electrical connection
Faulty Restraints Control Module (RCM)

How to Fix the DTC B007F Ford?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

B007F:11 Passenger Seatbelt Pretensioner 'C' Deployment Control: Circuit Short to Ground
B007F:12 Passenger Seatbelt Pretensioner 'C' Deployment Control: Circuit Short to Battery
B007F:13 Passenger Seatbelt Pretensioner 'C' Deployment Control: Circuit Open
B007F:1A Passenger Seatbelt Pretensioner 'C' Deployment Control: Circuit Resistance Below Threshold

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B007F Ford code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B007F Ford code?

Need more information on how to fix the B007F Ford code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B007F Ford code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B007F Ford Code

1. What does OBDII code B007F for Ford Passenger Seatbelt Pretensioner 'C' Deployment Control mean?

When this code appears, it indicates an issue with the deployment control of the passenger seatbelt pretensioner in a Ford vehicle.

2. What are the common symptoms of OBDII code B007F in a Ford vehicle?

Common symptoms include the airbag warning light staying illuminated on the dashboard and potential issues with the passenger seatbelt pretensioner system.

3. What are the possible causes of OBDII code B007F in a Ford vehicle?

Causes can include a faulty passenger seatbelt pretensioner, damaged wiring or connectors in the system, or a problem with the deployment control module.

4. How can I diagnose the OBDII code B007F in my Ford vehicle?

Diagnosis typically involves using an OBDII scanner to retrieve the specific fault code and then inspecting the passenger seatbelt pretensioner system for any visible damage or issues.

5. Can I continue driving my Ford vehicle with OBDII code B007F present?

It is not recommended to drive the vehicle with this code present, as it may indicate a potential safety issue with the passenger seatbelt pretensioner system.

6. How can I repair OBDII code B007F in my Ford vehicle?

Repair options may include replacing the faulty passenger seatbelt pretensioner, repairing damaged wiring or connectors, or reprogramming the deployment control module.

7. Is it possible to reset OBDII code B007F in a Ford vehicle without addressing the underlying issue?

While you may be able to clear the code temporarily, it is crucial to address the root cause of the problem to ensure the safety and functionality of the passenger seatbelt pretensioner system.

8. Are there any safety concerns associated with OBDII code B007F in a Ford vehicle?

Yes, this code relates to the passenger seatbelt pretensioner, which is a crucial safety component designed to enhance occupant protection in the event of a collision.

9. Can I fix OBDII code B007F in my Ford vehicle myself, or do I need to visit a mechanic?

Depending on your mechanical skills and access to tools, you may be able to address some aspects of the issue yourself. However, complex repairs or component replacements may require professional assistance.

10. How can I prevent OBDII code B007F from reoccurring in my Ford vehicle?

Regularly inspecting and maintaining the seatbelt pretensioner system, avoiding physical damage to the system, and addressing any warning lights promptly can help prevent the recurrence of this code.