AutoCodes – Lincoln – B007E Lincoln

B007E Lincoln Code - Driver Seatbelt Pretensioner 'C' Deployment Control

Quick Answer

The Restraints Control Module (RCM) analyzes the deployment loop resistance to determine if a fault exists. Common causes include Faulty Driver Seatbelt Pretensioner, Driver Seatbelt Pretensioner harness is open or shorted, Driver Seatbelt Pretensioner circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B007E Lincoln indicates Driver Seatbelt Pretensioner 'C' Deployment Control.
Common causes: Common causes include Faulty Driver Seatbelt Pretensioner, Driver Seatbelt Pretensioner harness is open or shorted, Driver Seatbelt Pretensioner circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 2,756

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Jun 14, 2020

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B007E Lincoln Description

The Restraints Control Module (RCM) analyzes the deployment loop resistance to determine if a fault exists. The value displayed in the PID is the deployment loop resistance measured by the RCM. If the value displayed is lower or higher than the desired range, the RCM can set a Diagnostic Trouble Code (DTC). As the deployment loop resistance drifts farther outside the desired range, the chance for a DTC increases. Small variations in resistance can occur due to the effect of road vibrations on terminal fit. Crimps and terminals can be affected by stress and harness movement and can cause an increase in resistance due to wire strain. These variables can result in an intermittent fault. For this reason, the test requires the PID value to be within the desired range before the fault is considered repaired, regardless if the module is reporting an on-demand DTC at the time of diagnosis. Following this direction helps make sure that minor changes in resistance do not create a repeat concern. This test uses the process of elimination to diagnose each part of the deployment loop circuit including:
- Wiring
- Connections
- Driver seatbelt anchor pretensioner
- RCM

OBDII Code B007E Lincoln - Driver Seatbelt Pretensioner 'C' Deployment Control - AutoCodes.com — B007E Lincoln Code - Driver Seatbelt Pretensioner 'C' Deployment Control

What does this mean?

What are the Possible Causes of the DTC B007E Lincoln?

Faulty Driver Seatbelt Pretensioner
Driver Seatbelt Pretensioner harness is open or shorted
Driver Seatbelt Pretensioner circuit poor electrical connection
Faulty Restraints Control Module (RCM)

How to Fix the DTC B007E Lincoln?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

B007E:11 Driver Seatbelt Pretensioner 'C' Deployment Control: Circuit Short to Ground
B007E:12 Driver Seatbelt Pretensioner 'C' Deployment Control: Circuit Short to Battery
B007E:13 Driver Seatbelt Pretensioner 'C' Deployment Control: Circuit Open
B007E:1A Driver Seatbelt Pretensioner 'C' Deployment Control: Circuit Resistance Below Threshold

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B007E Lincoln code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B007E Lincoln code?

Need more information on how to fix the B007E Lincoln code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B007E Lincoln code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B007E Lincoln Code

1. What are the common symptoms of OBDII code B007E in a Lincoln related to the Driver Seatbelt Pretensioner 'C' Deployment Control?

The common symptoms include the airbag warning light illuminating on the dashboard, potential non-deployment of the driver's seatbelt pretensioner during a collision, and diagnostic trouble codes indicating an issue with the seatbelt pretensioner.

2. What are the possible causes of OBDII code B007E in a Lincoln concerning the Driver Seatbelt Pretensioner 'C' Deployment Control?

The code B007E in a Lincoln can be caused by a faulty driver seatbelt pretensioner, damaged wiring or connectors in the seatbelt pretensioner circuit, or a malfunction in the deployment control module.

3. How can I diagnose OBDII code B007E in a Lincoln related to the Driver Seatbelt Pretensioner 'C' Deployment Control?

Diagnosing OBDII code B007E involves using a diagnostic scanner to retrieve the specific fault code, inspecting the seatbelt pretensioner and its connections for any visible damage, and testing the circuitry for continuity and proper voltage.

4. Is it safe to drive a Lincoln with OBDII code B007E related to the Driver Seatbelt Pretensioner 'C' Deployment Control?

It is not recommended to drive the vehicle with an active OBDII code B007E, as it indicates a potential issue with the driver seatbelt pretensioner, which is a crucial safety component in the event of a collision.

5. Can I reset OBDII code B007E in a Lincoln related to the Driver Seatbelt Pretensioner 'C' Deployment Control?

While you can clear the fault code using a diagnostic scanner, it is crucial to address the underlying issue causing the code to prevent any safety risks associated with the driver seatbelt pretensioner not functioning correctly.

6. How much does it typically cost to repair OBDII code B007E in a Lincoln concerning the Driver Seatbelt Pretensioner 'C' Deployment Control?

The cost of repairing OBDII code B007E can vary depending on the specific cause of the issue. It may involve replacing the driver seatbelt pretensioner, repairing damaged wiring, or addressing a fault in the deployment control module, which can range from moderate to expensive.

7. Can I fix OBDII code B007E related to the Driver Seatbelt Pretensioner 'C' Deployment Control in a Lincoln myself?

While some basic troubleshooting steps can be taken, diagnosing and repairing OBDII code B007E often requires specialized knowledge and tools. It is recommended to consult a professional mechanic or dealership for proper diagnosis and repair.

8. How long does it take to repair OBDII code B007E in a Lincoln associated with the Driver Seatbelt Pretensioner 'C' Deployment Control?

The repair time for OBDII code B007E can vary depending on the specific cause of the issue and the availability of parts. It may take anywhere from a few hours to a full day to diagnose and repair the problem effectively.

9. Are there any recalls or service bulletins related to OBDII code B007E in a Lincoln concerning the Driver Seatbelt Pretensioner 'C' Deployment Control?

It's advisable to check with the manufacturer or authorized service centers for any recalls or service bulletins related to OBDII code B007E in your specific Lincoln model. These resources may provide valuable information or potential assistance for addressing the issue.

10. What steps can I take to prevent OBDII code B007E related to the Driver Seatbelt Pretensioner 'C' Deployment Control from occurring in my Lincoln?

Routine maintenance and inspections of the seatbelt pretensioner system, avoiding physical damage to the seatbelt components, and addressing any warning lights or unusual behaviors promptly can help prevent OBDII code B007E and ensure the proper functioning of the safety system.