B0019:0E Code - Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Low Resistance
Quick Answer
During a side or frontal crash of sufficient force the inflatable restraint Sensing and Diagnostic Module (SDM) will allow current to flow through the deployment loop in order to deploy an air bag or pretensioner. Common causes include Faulty Passenger Instrument Panel Air Bag, Passenger Instrument Panel Air Bag harness is open or shorted, Passenger Instrument Panel Air Bag circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B0019:0E indicates Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Low Resistance.
- Common causes
- Common causes include Faulty Passenger Instrument Panel Air Bag, Passenger Instrument Panel Air Bag harness is open or shorted, Passenger Instrument Panel Air Bag circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code B0019:0E Description
What are the Possible Causes of the DTC B0019:0E?
- Faulty Passenger Instrument Panel Air Bag
- Passenger Instrument Panel Air Bag harness is open or shorted
- Passenger Instrument Panel Air Bag circuit poor electrical connection
- Faulty Sensing and Diagnostic Module (SDM)
How to Fix the DTC B0019:0E?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
B0019:02 Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Short to Ground
B0019:04 Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Open
B0019:0D Passenger Instrument Panel Air Bag Deployment Loop Stage 1 High Resistance
B0019:0E Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Low Resistance
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the B0019:0E code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the B0019:0E code?
Need more information on how to fix the B0019:0E code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B0019:0E code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B0019:0E Code
1. What does OBDII code B0019:0E mean?
It indicates a low resistance issue in the Passenger Instrument Panel Air Bag Deployment Loop Stage 1, which can affect airbag deployment functionality.
2. What are the symptoms of code B0019:0E?
Common symptoms include the airbag warning light illuminating and possible malfunction of the passenger airbag during a collision.
3. What causes code B0019:0E?
Causes can include damaged wiring, corroded connectors, a defective airbag module, or a short circuit in the deployment loop.
4. Can I still drive my vehicle with code B0019:0E?
While the vehicle may be drivable, the airbag system may not function properly in an accident, compromising safety.
5. How do I diagnose code B0019:0E?
Diagnosis involves inspecting the wiring harness and connectors, checking the resistance of the deployment loop, and scanning for additional airbag-related codes.
6. How is code B0019:0E typically repaired?
Repairs may include replacing damaged wiring, cleaning or replacing corroded connectors, or replacing the airbag module if defective.
7. Can code B0019:0E be cleared without fixing the issue?
Clearing the code without addressing the underlying problem will not resolve the malfunction and the code is likely to return.
8. Is code B0019:0E a common airbag issue?
Yes, low resistance in airbag deployment loops is a relatively common issue due to wear and tear or electrical faults.
9. How much does it cost to fix code B0019:0E?
Repair costs vary depending on the cause but can range from $100 for wiring repairs to over $1,000 for airbag module replacement.
10. Should I attempt to fix code B0019:0E myself?
Due to the complexity and importance of the airbag system, it is recommended to have a certified technician perform repairs to ensure safety.
Discuss the causes and fixes for B0019:0E OBDII Code
Code B0019:0E comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
