AutoCodes.com | All About OBDII Engine Codes
AutoCodes - Generic - B0016

B0016 Code - Left Roof Rail Deployment Loop Stage 1

- Code Popularity: 11,363 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
Share on Facebook   Share on Twitter   Share on Linkedin

What are the Possible Causes of the DTC B0016?

NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
  • Faulty Left Roof Rail Module
  • Left Roof Rail Module harness is open or shorted
  • Left Roof Rail Module circuit poor electrical connection
  • Faulty Sensing and Diagnostic Module (SDM)
⚠ Does your Car have Safety Recalls? → Check here

How to Fix the DTC B0016?

Review the 'Possible Causes' mentioned above and visually examine the corresponding wiring harness and connectors. Ensure to check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.

Code Tech Notes

B0016:01 Left Roof Rail Deployment Loop Stage 1 Short to Battery
B0016:02 Left Roof Rail Deployment Loop Stage 1 Short to Ground
B0016:04 Left Roof Rail Deployment Loop Stage 1 Open
B0016:0D Left Roof Rail Deployment Loop Stage 1 High Resistance
B0016:0E Left Roof Rail Deployment Loop Stage 1 Low Resistance

Search for B0016 Questions and Answers: Search here →

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B0016 code, it typically requires 1.0 hour of labor. The specific diagnosis time and labor rates at auto repair shops can differ based on factors such as the location, make and model of the vehicle, and even the engine type. It is common for most auto repair shops to charge between $75 and $150 per hour.

What are Code Possible Symptoms?

  • Air Bag Warning Light ON

Code B0016 Description

During a side or frontal crash of sufficient force the inflatable restraint Sensing and Diagnostic Module (SDM) will allow current to flow through the deployment loop in order to deploy an inflatable restraint module. There are 2 shorting bars used within the module connector which will short together both high and low circuits, when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing.

OBDII Code B0016 - Left Roof Rail Deployment Loop Stage 1 - AutoCodes.com
B0016 Code - Left Roof Rail Deployment Loop Stage 1

Need More Information on the Code?

Need more information on how to fix the B0016 code? Get Access to Factory Service Manuals

Information for Specific Makes

Need Help with the Code?

Get the B0016 code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

Code B0016 comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the B0016 code? Have you replaced any parts?
Any information is appreciated. Thanks