AutoCodes – Generic – B0014:01

B0014:01 Code - Driver Seat Side Air Bag Deployment Loop Short to Battery

Quick Answer

During a side or frontal crash of sufficient force the inflatable restraint Sensing and Diagnostic Module (SDM) will allow current flow through the deployment loop in order to deploy the side impact module. Common causes include Faulty Driver Seat Side Air Bag, Driver Seat Side Air Bag harness is open or shorted, Driver Seat Side Air Bag circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B0014:01 indicates Driver Seat Side Air Bag Deployment Loop Short to Battery.
Common causes: Common causes include Faulty Driver Seat Side Air Bag, Driver Seat Side Air Bag harness is open or shorted, Driver Seat Side Air Bag circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 355

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Oct 09, 2022

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B0014:01 Description

During a side or frontal crash of sufficient force the inflatable restraint Sensing and Diagnostic Module (SDM) will allow current flow through the deployment loop in order to deploy the side impact module. A shorting bar is located in the electrical connector of the side impact module. The side impact module high control circuit and low control circuit are shorted together by the shorting bar when the electrical connector is disconnected. The shorting bar helps prevent unwanted deployment of the inflator module during servicing. The SDM performs a continuous diagnostic test on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If the results of any deployment loop circuit test are below specifications the code B0014 and the appropriate symptom byte will be set. The Diagnostic Trouble Code (DTC) will be set when the air bag control circuit is shorted to voltage for 2 seconds.

OBDII Code B0014:01 - Driver Seat Side Air Bag Deployment Loop Short to Battery - AutoCodes.com — B0014:01 Code - Driver Seat Side Air Bag Deployment Loop Short to Battery

What does this mean?

What are the Possible Causes of the DTC B0014:01?

Faulty Driver Seat Side Air Bag
Driver Seat Side Air Bag harness is open or shorted
Driver Seat Side Air Bag circuit poor electrical connection
Faulty Sensing and Diagnostic Module (SDM)

How to Fix the DTC B0014:01?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

B0014:01 Driver Seat Side Air Bag Deployment Loop Short to Battery
B0014:02 Driver Seat Side Air Bag Deployment Loop Short to Ground
B0014:04 Driver Seat Side Air Bag Deployment Loop Open
B0014:0D Driver Seat Side Air Bag Deployment Loop High Resistance
B0014:0E Driver Seat Side Air Bag Deployment Loop Low Resistance

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B0014:01 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B0014:01 code?

Need more information on how to fix the B0014:01 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B0014:01 code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B0014:01 Code

1. What are the common symptoms of OBDII code B0014:01 related to the driver seat side airbag deployment loop short to battery?

The common symptoms include the airbag warning light illuminated on the dashboard, potential non-deployment of the driver seat side airbag during a collision, and possible diagnostic trouble codes stored in the vehicle's system.

2. What are the typical causes of OBDII code B0014:01 indicating a driver seat side airbag deployment loop short to battery?

The code is often triggered by a short circuit in the wiring harness leading to the driver seat side airbag, a faulty airbag deployment loop, or issues with the airbag control module.

3. How can I diagnose the issue causing OBDII code B0014:01 on my vehicle?

Diagnosing the problem involves using a professional OBDII scanner to retrieve the specific trouble codes, inspecting the wiring harness and connectors associated with the driver seat side airbag, and testing the airbag deployment loop for continuity.

4. Is it safe to drive my vehicle with OBDII code B0014:01 present?

It is not recommended to drive the vehicle with this code active, as it indicates a potential issue with the driver seat side airbag system, compromising occupant safety in the event of a collision.

5. Can I reset OBDII code B0014:01 on my own, or do I need to visit a mechanic?

While you can attempt to clear the code with an OBDII scanner, it is crucial to address the underlying problem causing the fault to ensure the airbag system's proper functionality. A mechanic's expertise may be necessary for a thorough diagnosis and repair.

6. What are some repair tips for resolving OBDII code B0014:01 related to the driver seat side airbag deployment loop short to battery?

Repair tips may include checking and repairing any damaged wiring, replacing the faulty airbag deployment loop, resetting the airbag control module, and conducting a thorough system test to ensure proper functionality.

7. Are there any safety precautions to consider when working on the driver seat side airbag system to fix OBDII code B0014:01?

It is essential to disconnect the vehicle's battery before working on the airbag system, follow proper safety procedures outlined in the vehicle's service manual, and consider seeking professional assistance if unsure about handling airbag components.

8. How much does it typically cost to repair OBDII code B0014:01 related to the driver seat side airbag deployment loop short to battery?

The cost of repair can vary depending on the extent of the damage, the need for replacement parts, and labor charges. It is advisable to obtain quotes from different mechanics or service centers for an accurate estimate.

9. Can OBDII code B0014:01 be a recurring issue even after repair?

If the root cause of the problem is not adequately addressed during the repair, there is a possibility of the code recurring. Thorough diagnosis and proper repair techniques can help prevent the issue from resurfacing.

10. How can I prevent OBDII code B0014:01 from occurring in the future?

Regular maintenance checks, prompt addressing of any warning lights related to the airbag system, and careful handling of the driver seat area to avoid damage to wiring can help prevent the recurrence of this code.