AutoCodes – Pontiac – B0013 Pontiac

B0013 Pontiac Code - Driver Frontal Deployment Loop Stage 2

Quick Answer

During a frontal crash of sufficient force, the inflatable restraint Sensing and Diagnostic Module (SDM) will allow current to flow through the deployment loop in order to deploy the steering wheel air bag. Common causes include Faulty Steering Wheel Air Bag, Faulty Steering Wheel Air Bag Coil, Steering Wheel Air Bag harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B0013 Pontiac indicates Driver Frontal Deployment Loop Stage 2.
Common causes: Common causes include Faulty Steering Wheel Air Bag, Faulty Steering Wheel Air Bag Coil, Steering Wheel Air Bag harness is open or shorted.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 4,263

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Oct 09, 2022

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B0013 Pontiac Description

During a frontal crash of sufficient force, the inflatable restraint Sensing and Diagnostic Module (SDM) will allow current to flow through the deployment loop in order to deploy the steering wheel air bag. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. There are two shorting bars used within the steering wheel air bag coil connector which will short together both steering wheel air bag stage 1 high control circuit and steering wheel air bag stage 1 low control circuit and both steering wheel air bag stage 2 high control circuit and steering wheel air bag stage 2 low control circuit when the connector is disconnected. This will help to prevent unwanted deployment of the steering wheel air bag during servicing.

OBDII Code B0013 Pontiac - Driver Frontal Deployment Loop Stage 2 - AutoCodes.com — B0013 Pontiac Code - Driver Frontal Deployment Loop Stage 2

What does this mean?

What are the Possible Causes of the DTC B0013 Pontiac?

Faulty Steering Wheel Air Bag
Faulty Steering Wheel Air Bag Coil
Steering Wheel Air Bag harness is open or shorted
Steering Wheel Air Bag circuit poor electrical connection
Faulty Sensing and Diagnostic Module (SDM)

How to Fix the DTC B0013 Pontiac?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

B0013:01 Driver Frontal Deployment Loop Stage 2 Short to Battery
B0013:02 Driver Frontal Deployment Loop Stage 2 Short to Ground
B0013:04 Driver Frontal Deployment Loop Stage 2 Open Circuit
B0013:0D Driver Frontal Deployment Loop Stage 2 High Resistance
B0013:0E Driver Frontal Deployment Loop Stage 2 Low Resistance

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B0013 Pontiac code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B0013 Pontiac code?

Need more information on how to fix the B0013 Pontiac code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B0013 Pontiac code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B0013 Pontiac Code

1. What are the common symptoms of OBDII code B0013 in a Pontiac related to the Driver Frontal Deployment Loop Stage 2?

- Common symptoms include the airbag warning light illuminating on the dashboard and potential non-deployment of the driver's frontal airbag during a collision.

2. What could be the possible causes of OBDII code B0013 in a Pontiac indicating an issue with the Driver Frontal Deployment Loop Stage 2?

- The code B0013 typically indicates a malfunction in the driver frontal airbag deployment loop, which could be caused by a faulty airbag sensor, wiring issues, or a problem with the airbag module.

3. How can I diagnose the OBDII code B0013 in my Pontiac related to the Driver Frontal Deployment Loop Stage 2?

- Diagnosing OBDII code B0013 requires using a compatible OBDII scanner to retrieve the specific fault code and then conducting a thorough inspection of the driver frontal airbag system components.

4. Are there any safety concerns associated with OBDII code B0013 Pontiac indicating a problem with the Driver Frontal Deployment Loop Stage 2?

- Yes, a malfunction in the driver frontal airbag system indicated by OBDII code B0013 can compromise the effectiveness of the airbag in a collision, posing a safety risk to the driver.

5. Can I continue driving my Pontiac with OBDII code B0013 related to the Driver Frontal Deployment Loop Stage 2?

- It is not recommended to drive the vehicle with unresolved airbag system issues indicated by OBDII code B0013, as the airbag may not deploy properly in an accident.

6. What are some repair tips for fixing OBDII code B0013 in a Pontiac involving the Driver Frontal Deployment Loop Stage 2?

- Repairing OBDII code B0013 may involve inspecting and repairing/replacing the driver frontal airbag sensor, checking and repairing the wiring harness, or replacing the airbag control module.

7. Can resetting the OBDII code B0013 in my Pontiac related to the Driver Frontal Deployment Loop Stage 2 solve the issue?

- Simply resetting the OBDII code B0013 may temporarily clear the warning light, but it will not fix the underlying issue causing the airbag system malfunction.

8. How much does it typically cost to repair OBDII code B0013 in a Pontiac due to Driver Frontal Deployment Loop Stage 2 problems?

- The cost of repairing OBDII code B0013 can vary depending on the specific cause of the issue, but it may range from a few hundred to over a thousand dollars, including parts and labor.

9. Are there any recalls or technical service bulletins related to OBDII code B0013 in Pontiac vehicles concerning the Driver Frontal Deployment Loop Stage 2?

- It's advisable to check with the manufacturer or a qualified dealership to see if there are any recalls or technical service bulletins related to OBDII code B0013 in your specific Pontiac model.

10. How can I prevent OBDII code B0013 from occurring again in my Pontiac involving the Driver Frontal Deployment Loop Stage 2?

- Regularly maintaining and inspecting the airbag system components, addressing any warning lights promptly, and following the manufacturer's recommended service schedule can help prevent OBDII code B0013 from reoccurring.