B0013 GMC - Driver Frontal Deployment Loop Stage 2

Repair Importance Level: 3/3
Repair Difficulty Level: 3/3   
Comments  |  Add Comment

B0013 GMC Possible Causes

  • Faulty Steering Wheel Inflator Module
  • Faulty Steering Wheel Module Coil
  • Steering Wheel Inflator Module harness is open or shorted
  • Steering Wheel Inflator Module circuit poor electrical connection
  • Faulty Sensing and Diagnostic Module (SDM)

First diagnose B0013 GMC code

    Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded terminals.

B0013 GMC Tech Notes

DTC B0013 01 Driver Frontal Deployment Loop Stage 2 Short to Battery
DTC B0013 02 Driver Frontal Deployment Loop Stage 2 Short to Ground
DTC B0013 04 Driver Frontal Deployment Loop Stage 2 Open Circuit
DTC B0013 0D Driver Frontal Deployment Loop Stage 2 Resistance Above Threshold
DTC B0013 0E Driver Frontal Deployment Loop Stage 2 Resistance Below Threshold

Cost of diagnosing the B0013 GMC code

    Labor: 1.0

    The cost of diagnosing the B0013 GMC code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle's make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

B0013 GMC Possible Symptoms

  • Air Bag Warning Light ON

B0013 Gmc Description

If a malfunction is detected, a Diagnostic Trouble Code (DTC) will be stored in non-volatile memory. During a frontal crash of sufficient force the inflatable restraint Sensing and Diagnostic Module (SDM) will allow current to flow through the deployment loop in order to deploy the steering wheel module. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. There are 2 shorting bars used within each connector which will short together both steering wheel module stage 1 high circuit and steering wheel module stage 1 low circuit and both steering wheel module stage 2 high circuit and steering wheel module stage 2 low circuit when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing.
OBDII Code B0013 Gmc - Driver Frontal Deployment Loop Stage 2 - AutoCodes.com

B0013 GMC More Information

Need more information on how to fix the B0013 GMC code?
Get Access to Factory Service Manuals

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

Need more help?

Get the B0013 Gmc code diagnosed by a professional: Find a repair shop in your area

Related Information

B0013 GMC Comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above help you fix the code. What are the symptoms on your vehicle for the B0013 Gmc code? Have you replaced any parts?
Any information is appreciated. Thanks
Top ⇧