| All About OBDII Engine Codes
AutoCodes - Ford - U3000 FORD

U3000 FORD Code - Control Module Failure Or Erratic

- Code Popularity: 75,705 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
By - Updated Jun 18, 2020
Share on Facebook   Share on Twitter   Share on Linkedin

|U3000 FORD code possible causes

  • Faulty Control Module
  • Control Module harness is open or shorted
  • Control Module circuit poor electrical connection

|How do I fix code U3000 FORD code?

Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.

Does your car have Safety Recalls? → Check here

|U3000 FORD code tech notes

  • U3000:42 (Control Module: General Memory Failure) - This Diagnostic Trouble Code (DTC) sets if the Power Steering Control Module (PSCM) detects an internal memory data error during the data plausibility check.
  • U3000:46 (Control Module: Calibration/Parameter Memory Failure) - This DTC sets if the PSCM detects an internal calibration data error during the data plausibility check.
  • U3000:49 (Control Module: Internal Electronic Failure) - If at any time during normal operation the PSCM detects an internal hardware error, DTC U3000:49 is set.
  • U3000:4B (Control Module: Over Temperature) - This DTC sets if the PSCM detects an internal over-temperature condition. Steering assist is reduced to protect the Electric Power-Assisted Steering (EPAS) electronics. Steering assist returns to the normal operating level when the system has cooled down.
  • U3000:53 (Control Module: Deactivated) - This DTC sets if the PSCM detects an internal error which causes a permanent de-activation which is not recoverable with an ignition cycle.
  • U3000:56 (Control Module: Invalid/Incomplete Configuration) - This DTC sets if the PSCM detects a mismatch of data structure in the non-volatile memory.
  • U3000:96 (Control Module: Component Internal Failure) - This DTC sets if a fault causes the EPAS to enter a failure mode.

  • |Cost of diagnosing U3000 FORD code

    Labor: 1.0

    The cost of diagnosing the U3000 FORD code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle's make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

    |What are U3000 FORD code possible symptoms?

    • Engine Light ON (or Service Engine Soon Warning Light)

    |U3000 FORD code description

    The Power Steering Control Module (PSCM) monitors various inputs and outputs of the Electric Power-Assisted Steering (EPAS) system in order to keep the system operating at peak capacity. Information provided by sensors (steering torque, vehicle speed, vehicle travel distance, etc.) are all compared to programmed and learned information. Likewise, outputs like the motor and steering rack (travel) are tested against programmed and learned information. The Diagnostic Trouble Code (DTC) will set when the PSCM detects a Control Module Failure Or Erratic.

    OBDII Code u3000 ford - Control Module Failure Or Erratic -
    U3000 FORD Code - Control Module Failure Or Erratic

    |Need more information with the U3000 FORD code?

    Need more information on how to fix the U3000 FORD code? Get Access to Factory Service Manuals

    |Need help with a U3000 FORD code?

    Get the u3000 ford code diagnosed by a professional: Find a repair shop in your area

    |U3000 FORD code comments

    Help us improve Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the u3000 ford code? Have you replaced any parts?
    Any information is appreciated. Thanks