AutoCodes.com | All About OBDII Engine Codes
AutoCodes - Buick - P22A4 Buick

P22A4 Buick Code - NOx Sensor 2 Heater Control Circuit Low Voltage

- Code Popularity: 117 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
Share on Facebook   Share on Twitter   Share on Linkedin

Code P22A4 Buick Possible Causes

  • Faulty Nitrogen Oxides (NOx) Sensor 2
  • Nitrogen Oxides Sensor 2 harness is open or shorted
  • Nitrogen Oxides Sensor 2 circuit poor electrical connection

How do I Fix the Code P22A4 Buick?

Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.

Does your Buick have Safety Recalls? → Check here

What is the Cost to Diagnose the Code P22A4 Buick?

Labor: 1.0

The cost of diagnosing the P22A4 Buick code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle's make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

What are Code P22A4 Buick Possible Symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)

Code P22A4 Buick Description

The Nitrogen Oxides (NOx) sensors are part of the selective catalytic reduction system, a device used to reduce NOx emission on diesel engines. There are two NOx sensors, one placed upstream of selective catalytic reduction, to measure inlet NOx concentration, and one placed downstream. They are connected with the control module via CAN and all the information is exchanged through it. Since it is a smart sensor, all the electrical monitoring is performed inside the sensor and only the results are sent to the Engine Control Module (ECM). Each NOx sensor contains a sensing cell, a pumping cell, and a heater. A sample of exhaust gas passes through a diffusion gap between the sensing cell and the pumping cell. The NOx sensor maintains a constant reference voltage across the sensing cell. An electronic circuit within the sensor controls the pump current through the pumping cell in order to maintain a constant voltage in the sensing cell. The amount of current required to maintain the reference voltage in the sensing cell is proportional to the concentration of NOx in the exhaust. The ECM varies the amount of diesel exhaust fluid (reductant) added by varying the reductant injector duty cycle in response to changes in engine exhaust NOx levels. The smart NOx sensors consist of two components, the NOx module and the NOx sensor element that are serviced as a unit. A circuit or performance condition with a NOx sensor is detected by the NOx sensor module. The smart NOx sensor module communicates the condition to the ECM over the serial data line. The ECM sets a DTC when a serial data message is received from the NOx sensor module. The Diagnostic Trouble Code (DTC) will be set if the ECM software detects a fault in the NOx sensor circuitry or a performance fault in the NOx sensor for greater than 2 s.

OBDII Code P22A4 Buick - NOx Sensor 2 Heater Control Circuit Low Voltage - AutoCodes.com
P22A4 Buick Code - NOx Sensor 2 Heater Control Circuit Low Voltage

Need More Information on the P22A4 Buick Code?

Need more information on how to fix the P22A4 Buick code? Get Access to Factory Service Manuals

Need Help with the P22A4 Buick Code?

Get the P22A4 Buick code diagnosed by a professional: Find a repair shop in your area

Code P22A4 Buick comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the P22A4 Buick code? Have you replaced any parts?
Any information is appreciated. Thanks