P0300 CHEVROLET - Cylinder Misfire Detected Random Cylinders
P0300 CHEVROLET Possible Causes
- Faulty spark plug (s)
- Faulty ignition coil (s)
- Clogged or faulty fuel injector (s)
- Intake air leak
- Fuel injectors harness is open or shorted
- Fuel Injectors circuit poor electrical connection
- Ignition coils harness is open or shorted
- Ignition coils circuit poor electrical connection
- Insufficient cylinders compression
- Incorrect fuel pressure
How do I fix code P0300 CHEVROLET?Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.
How much do you know about cars?
Take the AutoCodes.com automotive tests and turbo-charge your car repair knowledge
There are Factory Service Bulletins for the following Chevrolet models:
All 2000-2013 Chevrolet Models:
2000-2013Chevrolet Factory Service Bulletin OBDII Code P0300
2014 Chevrolet Silverado 1500
2014-2016 Chevrolet Corvette
2015-2016 Chevrolet Silverado
2015-2016 Chevrolet Suburban
2015-2016 Chevrolet Tahoe
2016 Chevrolet Camaro
Chevrolet Factory Service Bulletin OBDII Code P0300
2005-2006 Chevrolet Impala
2005-2006 Chevrolet Monte Carlo
2005-2006 Chevrolet TrailBlazer Models
2007 Chevrolet Avalanche
2007 Chevrolet Suburban
2007 Chevrolet Tahoe
Chevrolet Factory Service Bulletin OBDII Code P0171
2000-2018 Chevrolet All Models
2000-2018 Chevrolet Factory Service Bulletin OBDII Code P0300
This Factory Service Bulletin explains how this condition may be caused by significant carbon build up on the intake and/or exhaust valves due to fuel contamination or incomplete burning of the fuel.
2002 Chevrolet Blazer P0300 Misfire Diagnostics
User Submitted Video
Cost of diagnosing the P0300 CHEVROLET code
Labor: 1.0The cost of diagnosing the P0300 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle's make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/loss of power
- Hard start
- Engine hesitation
P0300 CHEVROLET DescriptionThe Engine Control Module (ECM) uses information from the crankshaft position sensor and the camshaft position sensor to determine when an engine cylinder misfire is occurring. By monitoring variations in the crankshaft rotation speed for each cylinder, the ECM can detect individual cylinder misfire events.
Extreme cylinder misfire events can cause catalytic converter damage. The malfunction indicator lamp (MIL) will flash when the conditions for catalytic converter damage are present. The Diagnostic Trouble Codes (DTC) P0301 through P0306 (or P0301 through P0308) correspond to cylinders 1 through 6 (or 1 through 8). When the ECM detects that one or more specific cylinders are misfiring, the DTC for the respective misfiring cylinder will set, and up to 2 of the corresponding fuel injectors are disabled for a minimum of 30 s. The ECM will then re-enable the fuel injector and, after approximately 200 engine revolutions, will determine if the misfire is still present. If the misfire is still present, the ECM will disable the fuel injector again repeating the process. If the misfire is not present, the fuel injector will remain enabled by the ECM. In Spark Ignition Direct Injection (SIDI) system applications, if a fuel injector fault DTC is set during a misfire event, the ECM will not re-enable the injector.
More InformationNeed more information on how to fix the P0300 CHEVROLET code?
Get Access to Factory Service Manuals
Information for specific Chevrolet models
Need more help?Get the P0300 Chevrolet code diagnosed by a professional: Find a repair shop in your area
CommentsHelp us improve AutoCodes.com. Leave a comment below or tell us if the information above help you fix the code. What are the symptoms on your vehicle for the P0300 Chevrolet code? Have you replaced any parts?
Any information is appreciated. Thanks