P0016 CHEVROLET - Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor 'A'
P0016 CHEVROLET Possible Causes
- Mechanical timing fault (stretched timing chain or damage timing chain tensioner)
- Blocked oil passage
- Low oil level
- Faulty Intake ('A') Camshaft Position (CMP) Sensor
- Faulty Crankshaft Position (CKP) Sensor
First diagnose P0016 CHEVROLET code
Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded terminals.
P0016 CHEVROLET Tech NotesIf this DTC started after recent internal engine repairs, inspect for proper engine mechanical timing. With the camshaft cover removed and the #1 cylinder at top dead center, make sure that the darkened chain links are lined up with the alignment marks on the exhaust and intake cam sprockets.
If a P0016 is resetting without any engine performance concerns but the above information did not isolate a cause for the DTC, replace the Cam Phaser Actuator sprocket.
There is a factory service bulletin for the following Chevrolet models:
2008-2012 Chevrolet Captiva
2008-2012 Chevrolet Equinox
2008-2012 Chevrolet Malibu
2009-2012 Chevrolet Traverse
2010-2012 Chevrolet Camaro
2012 Chevrolet Impala
Chevrolet Factory Service Bulletin OBDII Code P0016
Cost of diagnosing the P0016 CHEVROLET code
Labor: 1.0The cost of diagnosing the P0016 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle's make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.
When is the P0016 CHEVROLET code detected?The Powertrain Control Module (PCM) has detected the actual Camshaft Position (CMP) Sensor angle of one camshaft is greater or less than the commanded state.
P0016 CHEVROLET Possible Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Engine hard to start
- Engine stall while driving
P0016 Chevrolet DescriptionThe Crankshaft Position (CKP) sensor is a permanent magnet generator, known as a variable reluctance sensor. The magnetic field of the sensor is altered by a crankshaft mounted reluctor wheel that has seven machined slots, 6 of which are equally spaced 60 degrees apart. The seventh slot is spaced 10 degrees after one of the 60 degree slots. The CKP sensor produces seven pulses for each revolution of the crankshaft. The pulse from the 10 degree slot is known as the sync pulse. The sync pulse is used to synchronize the coil firing sequence with the crankshaft position. The CKP sensor is connected to the Powertrain Control Module (PCM) by a signal circuit and a low reference circuit.
The Camshaft Position (CMP) sensor is triggered by a notched reluctor wheel built into the exhaust camshaft sprocket. The CMP sensor provides 6 signal pulses every camshaft revolution. Each notch, or feature of the reluctor wheel is of a different size for individual cylinder identification. This means the CMP and crankshaft position (CKP) signals are pulse width encoded to enable the PCM to constantly monitor their relationship. This relationship is used to determine camshaft actuator position and control its phasing at the correct value. The PCM also uses this signal to identify the compression stroke of each cylinder, and for sequential fuel injection. The CMP sensor is connected to the PCM by a 12-volt, low reference, and signal circuit.
P0016 CHEVROLET More InformationNeed more information on how to fix the P0016 CHEVROLET code?
Get Access to Factory Service Manuals
Need more help?Get the P0016 Chevrolet code diagnosed by a professional: Find a repair shop in your area
P0016 CHEVROLET CommentsHelp us improve AutoCodes.com. Leave a comment below or tell us if the information above help you fix the code. What are the symptoms on your vehicle for the P0016 Chevrolet code? Have you replaced any parts?
Any information is appreciated. Thanks