| All About OBDII Engine Codes
AutoCodes - Generic - B0001

B0001 Code - Driver Frontal Stage 1 Deployment Control

- Code Popularity: 46,967 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
By - Updated Mar 01, 2019
Share on Facebook   Share on Twitter   Share on Linkedin

|B0001 code possible causes

  • Faulty Driver Side Air Bag
  • Driver Side Air Bag harness is open or shorted
  • Driver Side Air Bag circuit poor electrical connection
  • Faulty Clockspring
  • Faulty Restraints Control Module (RCM)

|How do I fix code B0001 code?

Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.

Does your car have Safety Recalls? → Check here

|B0001 code tech notes

B0001:11 Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground
B0001:12 Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery
B0001:13 Driver Frontal Stage 1 Deployment Control: Circuit Open
B0001:1A Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold

|Cost of diagnosing B0001 code

Labor: 1.0

The cost of diagnosing the B0001 code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle's make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

|When is the B0001 code detected?

If the Restraints Control Module detects a short between the driver air bag stage 1 circuits and the circuits of another SRS component, it sets this Detected Trouble Code (DTC) and the DTC of the corresponding SRS component.

|What are B0001 code possible symptoms?

  • Air Bag Warning Light ON

|B0001 code description

The Restraints Control Module (RCM) monitors all deployable device and sensor circuits for a signal cross coupled (short) between circuits. If the RCM detects a short between the circuits of one device and another device, it will store a DTC for each of the signal cross coupled faults in memory. The RCM sends a message to the Instrument Panel Cluster (IPC) to illuminate the air bag warning indicator. When a normal loop fault is present (one loop is either shorted to battery/ground, open circuit or low resistance), then signal cross coupled diagnostics will not be active. Once the normal loop fault is repaired, then the signal cross coupled diagnostics will resume.

OBDII Code b0001 - Driver Frontal Stage 1 Deployment Control -
B0001 Code - Driver Frontal Stage 1 Deployment Control

|Need more information with the B0001 code?

Need more information on how to fix the B0001 code? Get Access to Factory Service Manuals

|Information for specific makes

|Need help with a B0001 code?

Get the b0001 code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

|B0001 code comments

Help us improve Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the b0001 code? Have you replaced any parts?
Any information is appreciated. Thanks