AutoCodes.com | All About OBDII Engine Codes
AutoCodes - Generic - B1862

B1862 Code - Short to Ground in Driver Side Knee Airbag Squib Circuit

- Code Popularity: 4,567 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
Share on Facebook   Share on Twitter   Share on Linkedin

What are the Possible Causes of the DTC B1862?

NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
  • Faulty Driver Side Knee Airbag Assembly (Driver Side Knee Squib)
  • Driver Side Knee Airbag Assembly harness is open or shorted
  • Driver Side Knee Airbag Assembly circuit poor electrical connection
  • Faulty Center Airbag Sensor Assembly
⚠ Does your Car have Safety Recalls? → Check here

How to Fix the DTC B1862?

Review the 'Possible Causes' mentioned above and visually examine the corresponding wiring harness and connectors. Ensure to check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.

Search for B1862 Questions and Answers: Search here →

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B1862 code, it typically requires 1.0 hour of labor. The specific diagnosis time and labor rates at auto repair shops can differ based on factors such as the location, make and model of the vehicle, and even the engine type. It is common for most auto repair shops to charge between $75 and $150 per hour.

What are Code Possible Symptoms?

  • Air Bag Warning Light ON

Code B1862 Description

The Driver Side Knee Airbag Squib Circuit consists of the Center Airbag Sensor Assembly and the Driver Side Knee Airbag Assembly. This circuit instructs the Supplemental Restraint System (SRS) to deploy when deployment conditions are met. The Diagnostic Trouble Code (DTC) is stored when a malfunction is detected in the Driver Side Knee Airbag Squib Circuit.

OBDII Code B1862 - Short to Ground in Driver Side Knee Airbag Squib Circuit - AutoCodes.com
B1862 Code - Short to Ground in Driver Side Knee Airbag Squib Circuit

Need More Information on the Code?

Need more information on how to fix the B1862 code? Get Access to Factory Service Manuals

Information for Specific Makes

  • B1862 Lexus Short to Ground in Driver Side Knee Airbag Squib Circuit  📷
  • B1862 Scion Short to Ground in Driver Side Knee Airbag Squib Circuit  📷
  • B1862 Toyota Short to Ground in Driver Side Knee Airbag Squib Circuit  📷

Need Help with the Code?

Get the B1862 code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

Code B1862 comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the B1862 code? Have you replaced any parts?
Any information is appreciated. Thanks